NOTICE D´UTILISATION
5
Mise en service /
commande
voir fig. 33
Attention!
Ne pas procéder à une marche d'essai
du moteur tant qu'il n'y a pas d'eau
dans la pompe. Une marche à sec de
la
pompe
mécanique d'étanchéité !
•
Mise en marche/arrêt de la pompe
Une pression du bouton-poussoir (A) actionne le
commutateur pneumatique, la pompe démarre, une
nouvelle pression l'arrête (fonction marche/arrêt).
•
Réglage du jet d'eau
Le jet d'eau devient plus faible en faisant tourner la
poignée (B) dans le sens des aiguilles d'une montre
et plus puissant dans l'autre sens.
•
Régulation de l'air / bain bouillonnant
L'arrivée d'air devient plus faible en faisant tourner
la poignée (C) dans le sens des aiguilles d'une
montre et plus puissant dans l'autre sens. L'addition
d'air dans l'eau a pour effet d'adoucir l'impact du jet
d'eau (bain bouillonnant).
•
Direction du jet
La buse est orientable dans tous les sens.
•
Nage à contre-courant
Régler le jet sur sa puissance maximale. Orienter la
buse (D) de manière à créer un fort courant
directement au-dessous du niveau de l'eau.
•
Accouplement et désaccouplement du
lot de massage
Arrêter le dispositif de nage à contre-courant avant
de mettre en place ou de retirer la buse de massage
par impulsion.
Accouplement (voir fig. 34):
manchon coulissant (E), enfoncer le raccord
symétrique (F) dans la buse (D), presser le
manchon coulissant (E) contre la buse (D) et
repousser le raccord symétrique (F) qui est ainsi
verrouillé.
Désaccouplement (voir fig. 35): Presser le raccord
symétrique (F) contre le manchon coulissant (E),
saisir et repousser ce dernier, extraire le raccord.
C2G-rondo
27201-C
détruit
sa
garniture
Repousser le
Schmalenberger GmbH + Co.
D-72072 Tübingen / Germany
OPERATOR´S MANUAL
5
Start-Up and Operation
see fig. 33
Warning!
Never start the motor unless the
pump is
operation
irreparable damage to the pump seal!
•
Switching the pump on and off
The pneumatic switch is actuated when the
pushbutton (A) is pressed. The pump then starts.
Pump operation is stopped when the pushbutton is
pressed a second time (ON-OFF function).
•
Regulating the jet
Turning the knob (B) clockwise reduces the water
flow. The flow is increased when the knob is turned
anti-clockwise.
•
Regulating the air / bubble bath
Turning the knob (C) clockwise reduces the air
supply, turning the knob anti-clockwise increases
the air supply. The air supply in the water reduces
the intensity of the jet (bubble bath).
•
Direction of the jet
The jet can be swivelled in all directions.
•
Swimming against the current
Adjust the jet to full power. Swivel the nozzle (D) so
that a strong current is created immediately below
the surface of the water.
•
Connecting and disconnecting the
massage set
Prior to connecting or disconnecting the pulse
massage nozzle, switch off the counter-current unit.
Connecting (see fig. 34):
sleeve (E), insert the hose coupling (F) into the
nozzle (D), press the sliding sleeve (E) against the
nozzle (D) and pull back the hose coupling. (F). The
hose coupling is then locked in position.
Disconnecting (see fig. 35): Push the hose
coupling (F) against the sliding sleeve (E). Grasp
the sleeve and pull back, pull out the hose coupling.
filled with water. Dry
of
the
pump
causes
Pull back the sliding
51