Horizon Hobby E-FLITE Turbo Timber SWS 2.0m EFL71750 Manuel D'utilisation page 4

EN
Transmitter Setup BNF Basic
Dual Rates
Take first flights in Low Rate. For landings, use high rate elevator.
NOTICE: To ensure AS3X
® technology functions properly, do not lower rate
values below 50%. If lower rates are desired, manually adjust the position of the
pushrods on the servo arm.
NOTICE: If oscillation occurs at high speed, refer to the Troubleshooting Guide
for more information.
Exponential
After first flights, you may adjust exponential in your transmitter.
Telemetry Setup
See the Telemetry Setup table after binding. In order for the ESC and battery
information to auto-populate in your transmitter's telemetry menu, you must begin
telemetry setup with the aircraft bound and connected.
DX Series Transmitter Setup
1. Power ON your transmitter, click on scroll wheel, roll to System Setup and click the
scroll wheel. Choose yes.
2. Go to Model Select and choose <Add New Model> at the bottom of the list. The
system asks if you want to create a new model, select Create
3. Set Model Type: Select Airplane Model Type by choosing the airplane.
The system asks you to confirm model type, data will be reset. Select YES
4. Set Model Name: Input a name for your model file
5. Scroll to Aircraft type, click on the roller. Scroll to Wing: click on the roller and scroll
to select 1Ail 1Flap.
6. Select <Main Screen>, Click the scroll wheel to enter the Function List
7. Set D/R (Dual Rate) and Expo; Aileron
Set Switch: Switch F
Set High Rates: 100%, Expo 10% - Low Rates: 70%, Expo 5%
8. Set D/R (Dual Rate) and Expo; Elevator
Set Switch: SWITCH C
Set High Rates: 100%, Expo 10% - Low Rates 70%, Expo 5%
9. Scroll to Throttle Cut; Switch: Switch H, Position: -100%
10. Scroll to Flap System
Set SWITCH D
Set POS 0: 0% FLAP 0% Elevator
Set POS 1: 38% FLAP 3% Elevator
Set POS 2: 68% FLAP 9% Elevator
Set SPEED 2.0s
4
NX Series Transmitter Setup
1. Power ON your transmitter, click on scroll wheel, roll to System Setup and click the
scroll wheel. Choose yes.
2. Go to Model Select, click on the scroll wheel, and choose <Add New Model> near the
bottom of the list. Select Airplane Model Type by choosing the airplane, select Create
3. Set Model Name: Input a name for your model file
4. Scroll to Aircraft type, click on the roller. Scroll to Wing: click on the roller and scroll to
select 1Ail 1Flap.
5. Select <Main Screen>, Click the scroll wheel to enter the Function List
6. Set Rates and Expo; Aileron
Set Switch: Switch F
Set High Rates: 100%, Expo 10% - Low Rates: 70%, Expo 5%
7. Set Rates and Expo; Elevator
Set Switch: SWITCH C
Set High Rates: 100%, Expo 10% - Low Rates 70%, Expo 5%
8. Scroll to Throttle Cut; Switch: Switch H, Position: -100%
9. Scroll to Flap System
Set SWITCH D
Set POS 0: 0% FLAP 0% Elevator
Set POS 1: 38% FLAP 3% Elevator
Set POS 2: 68% FLAP 9% Elevator
Set SPEED 2.0s
iX Series Transmitter Setup
1. Power ON your transmitter and begin once the Spektrum Airware app is open.
Select the orange pen icon in the upper left corner of the screen, the system asks for
permission to Turn Off RF, select PROCEED
2. Select the three dots in the upper right corner of the screen,
select Add a New Model
3. Select Model Option, choose DEFAULT, select Airplane.
The system asks if you want to create a new acro model, select Create
4. Select the last model on the list, named Acro.
Tap on the word Acro and rename the file to a name of your choice
5. Tap and hold the back arrow icon in the upper left corner of the screen to return to the
main screen
6. Go to Model Setup menu. Select Aircraft Type The system asks for permission to
Turn Off RF, select PROCEED.
Touch the screen to select wing. Select 1 Ail 1 Flap.
7. Press and hold the back arrow icon in the upper left corner of the screen to return to
the main screen.
8. Go to the Model Adjust menu
9. Set Dual Rates and Expo; Select Aileron
Set Switch: Switch F
Set High Rates: 100%, Expo 10% - Low Rates: 70%, Expo 5%
10. Set Dual Rates and Expo; Select Elevator
Set Switch: SWITCH C
Set High Rates: 100%, Expo 10% - Low Rates 70%, Expo 5%
11. Select Flap System
Set SWITCH D
Set POS 0: 0% FLAP 0% Elevator
Set POS 1: 38% FLAP 3% Elevator
Set POS 2: 68% FLAP 9% Elevator
Set SPEED 2.0s
12. Select Throttle Cut; Switch: Switch H, Position: -100%
Turbo Timber SWS 2.0m