Horizon Hobby E-FLITE Turbo Timber SWS 2.0m EFL71750 Manuel D'utilisation page 22

EN
SAFE Select Switch Designation BNF Basic
®
Once SAFE Select is enabled, you can choose to fly in SAFE mode full time, or
assign a switch. Any switch on any channel between 5 and 9 can be used on your
transmitter.
TIP: If model has a reversing ESC feature, Aux2 is not available for SAFE select.
If the aircraft is bound with SAFE Select disabled, the aircraft will be in AS3X mode
exclusively.
CAUTION: Keep all body parts well clear of the propeller and keep the
aircraft securely restrained in case of accidental throttle activation.
IMPORTANT: To be able to assign a switch, first verify:
• The aircraft was bound with SAFE Select enabled.
• Your choice for the SAFE Select switch is assigned to a channel between
5 and 9 (Gear, Aux1-4), and travel is set at 100% in each direction.
• The aileron, elevator, rudder and throttle direction are set to normal,
not reverse.
• The aileron, elevator, rudder and throttle are set to 100% travel. If dual
rates are in use, the switches need to be in the 100% position.
See your transmitter manual for more information about assigning a switch
to a channel.
Smart Technology Telemetry BNF Basic
™
Smart Technology Electronic Speed Control (ESC)
This aircraft is equipped with an exclusive Smart technology electronic speed
control that can provide a variety of real-time power system related telemetry data
while you fly, including motor RPM, current, battery voltage and more to compatible
Spektrum AirWare equipped transmitters.
™
When powered on, the ESC will send the below information to the flight control and
the information will be displayed on the transmitter telemetry screen.
• RPM*
• Voltage
• Current
* During binding the transmitter will perform an auto configuration which will
populate the telemetry page. You may need to change the telemetry values on
those pages to suit this aircraft and your needs.
To enter the telemetry values:
(For iX series transmitters, you must select Save on each page)
1. Power on your transmitter.
2. Set the throttle cut to on.
3. Power on the aircraft and allow it to initialize.
4. In your transmitter, go to the Function List
(Model Setup in iX series transmitters).
5. Select the Telemetry menu option.
6. Go to the Smart Battery menu option.
7. Scroll down to Startup Volts, enter 4.0V/cell.
8. Return to the Telemetry menu.
9. Go to the Smart ESC menu option.
10. Scroll down to Low Voltage Alarm, enter 3.4V/cell.
11. Scroll down to Poles, enter 14.
12. Return to the main screen.
22
• Throttle
• FET Temperature
• BEC Temperature
Assigning a Switch
1. Power on the transmitter.
2. Power on the aircraft.
3. Hold both transmitter sticks to the inside bottom corners, and toggle the desired
switch 5 times quickly (1 toggle = full up and down).
4. The control surfaces of the aircraft will move, indicating the switch has been
selected.
Repeat the process to assign a different switch or to deactivate the current switch.
SAFE Select Switch Assignment Stick Positions
Mode 1 and 2 transmitters
TIP: Use the channel monitor to verify channel movement.
Monitor
-100 100 -100 -100
THR AIL ELE RUD
This example of the channel monitor shows the stick positions for assigning a
switch, the switch selection on Aux3, and +/- 100% travel on the switch.
DX/NX screen shots shown below
Telemetry Alarms
Smart Battery : Startup Voltage Minimum
Smart ESC : Low Voltage Alarm
Smart ESC : Motor Poles
Turbo Timber SWS 2.0m
Assigned Switch
100%
X 5
100%
+/-100
-100 -100 -100 -100
GER AX1 AX2 AX3 AX4
4.0V
3.4V
14