socomec ATyS 3e Notice D'utilisation page 93

Control circuits ATyS 6e
Denomination Terminals (1) Description
Power supply Power 101 Source
1
230 V~102
Power supply Power 201 Source
2
230 V~202
Sensing inputs N (103) Neutral
1
source L3 (104) Phase 3
L2 (105) Phase 2
L1 (106) Phase 1
Sensing inputs L1 (203) Phase 1
2
source L2 (204) Phase 2
L3 (205) Phase 3
N (206) Neutral
Commands 207 Commands inputs Common terminal
208 Standby source transfer control input (CTS)
209 Remote test on load input
210 DC power supply for 2I / 2O
Genset 73 Genset start / stop relay - 2 stable positions
start signal (2) 74 Programmable state - factory setting = NO, close to start 5A AC1 / 250 V
Control 313 Control activation
(Impulse / if closed with 317
contactor 314 Position II order if closed with 317
mode to 315 Position I order if closed with 317
change 316 Position 0 order if closed with 317
programming) 317 Specific voltage supply
Common control terminals 313 to 316
Remote interface RJ ATyS D10 or D20 connection
conection
Position 13 Common I - 0 - II
auxiliary 14 AC position I NO
contacts 24 AC position II NO
34 AC position 0 NO
Auxiliary 43 Auto / manu selector position
contacts 44 Closed in automatic position
/ AUT & 53 Padlocked information
Padlock 54 Closed if padlock is in place
Fault 63 Relay closed when product is faulty
relay 64 (if product is powered)
Second 81 Common AC position I
auxiliary 82 AC position I NC
contact 84 AC position I NO
(option) 91 Common AC position II
92 AC position II NC
94 AC position II NO
Option 0 Connection RS485
Communication -
+
Option I13 + Input
2 Inputs / I14 - Function according to programming
2 Outputs I23 + Input
I24 - Function according to programming
O13 Output Relay
O14 Function according to programming
O23 Output Relay
O24 Function according to programming
Voltage and frequency sensing precision: 1 %
(1) Terminal numbers can differ depending on voltage sensing and power supply kit configuration.
(2) Refer to programming, Setup, to modify relay state.
(3) It is recommended to power 2I / 2O modules from terminals 207-210 (refer to connection diagram).
SOCOMEC - Réf.: 531 848 F
1
2
Automatic Transfer Switch ATyS
CONNECTIONS
Characteristics
220 to 240 Vac ±20 %
500 Vac (phase-phase)
maximum
288 Vac (phase-neutral)
maximum
500 Vac (phase-phase)
maximum
288 Vac (phase-neutral)
maximum
Do not connect to any
power supply
Dry contact
Do not connect to any
power supply
Maximum distance 3 m.
5A AC1 / 250 V
5A AC1 / 250 V
5A AC1 / 250 V
5A AC1 / 250 V
To power from 10 to 30 Vdc (3)
(3)
To power from 10 to 30 Vdc
5A AC1 / 250 V
Recommended
section
2
1.5 mm
1.5 mm 2
1.5 mm 2
2
1.5 mm
4 mm 2
1.5 mm 2
RJ45 8 / 8
1.5 mm 2
1.5 mm 2
1.5 mm 2
2
1.5 mm
1.5 mm 2
2
1.5 mm
1.5 mm 2
93