JUKI MEB-3200 Manuel D'utilisation page 83

No. Function
14 Start Sw
One-touch startng selecton
Wth/wthout
17 Functon key F1
Data No. settng
18 Functon F2 key
Data No. settng
19 Wth/wthout settng of thread tenson
compensaton value
Wth/wthout
20 Selecton of data settng prohbton
Permtted/prohbted
22 Looper thread trmmng control
23 Presser comes down when returnng to set
poston
24 Temporary stop of cut-after knfe
26 Straght bar and cloth open
29 Front set poston
40 Knfe pressng amount data settng accepted
41 Knfe pressng amount (Knfe holder No.1)
42 Knfe pressng amount (Knfe holder No.2)
43 Knfe pressng amount (Knfe holder No.3)
44 Knfe pressng amount (Knfe holder No.4)
45 Knfe pressng amount (Knfe holder No.5)
46 Knfe pressng amount (Knfe holder No.6)
47 Knfe pressng amount (Knfe holder No.7)
48 Knfe pressng amount (Knfe holder No.8)
49 Knfe pressng amount (Knfe holder No.9)
50 Knfe pressng amount (Knfe holder No.0)
55 Knfe lower stop tme
57 Number of low speed pulses to lower knfe
motor
58 Number of low speed pulses to lft knfe motor
65 Wth/wthout needle thread clamp
66 Number of sttches to open needle thread
clamp
69 Needle thread clamp travellng amount
B8 Needle thread draw-n 2-stage operaton
C0 Lengthwse speed at the tme of needle
thread clamp
＊ H9 through L9 are displayed as well. However, they are the memory switches for the multicutting device.
For the sewing machine not provided with the multicutting device, they are not effective even when the setting
is changed.
Description
Whether startng by start swtch only s possble s selected.
0 : Presser comes down by presser swtch, the machne
s started by start swtch
1 : Presser comes down by start swtch and the machne
starts (Presser swtch s operatve as well.)
Data Nos. whch are aassgned to Functon F1 key are set.
(Intal value ... Knfe poston compensaton)
Data Nos. whch are assgned to Functon F2 key are set.
(Intal value ... Copy destnaton No.)
Whether to set thread tenson compensaton value wth
NEEDLE/LOOPER key s selected.
0 : Wthout settng
1 : Wth settng
Whether to prohbt data settng s selected.
0 : Permtted
1 : Prohbted (Thread tenson s possble.)
Wth/wthout looper thread trmmng operaton s set.
0 : Wthout
1 : Wth
Whether presser returns to set poston whle t s lowered
after sewng s selected.
0 : Presser goes up and returns to set poston.
1 : Presser returns to set poston whle t s lowered and goes up.
Whether to automatcally stop temporarly before
operaton of cut-after knfe and to make the knfe operate
by start swtch s selected.
0 : Normal operaton
1 : Cut-after knfe automatcally stops temporarly before
operaton and s operated by start swtch.
Whether to perform sewng wth the cloth open mechansm
opened n case of the pattern n whch straght bar s set.
0 : Normal operaton
1 : Settng cloth wth cloth open mechansm opened
Poston from the orgn s set when "front" s selected wth
memory swtch No. 11.
Whether knfe holder No. to whch knfe pressng amount
has been set s set to pattern data s selected.
0 : Without (Knife holder No.0 fixed)
1 : Wth (Knfe holer Nos.0 to 9 set)
Knfe pressng amount of knfe holder No.1
Knfe pressng amount of knfe holder No.2
Knfe pressng amount of knfe holder No.3
Knfe pressng amount of knfe holder No.4
Knfe pressng amount of knfe holder No.5
Knfe pressng amount of knfe holder No.6
Knfe pressng amount of knfe holder No.7
Knfe pressng amount of knfe holder No.8
Knfe pressng amount of knfe holder No.9
Knfe pressng amount of knfe holder No.0
Perod of tme of stoppng at the lower poston of knfe
Cuttng speed secton at the tme of cloth cuttng (Down)
Cuttng speed secton at the tme of cloth cuttng (UP)
Wth/wthout needle thread clamp operaton s set.
0 : Wthout
1 : Wth
Number of sttches at sewng start to open needle thread
clamp s set.
Settng of travellng amount by mm from end of sewng to
close thread clamp
0 : 1-stage operaton
1 : 2-stage operaton
Lengthwse jump feed speed from end of sewng to
needle thread clamp
Setting Setting Initial
range unit value
0 to 1 - 0
0 to 80 - 8
0 to 80 - 0
0 to 1 - 0
0 to 1 - 0
0 to 1 - 1
0 to 1 - 0
0 to 1 - 0
0 to 1 - 0
0 to 64 1 mm 22
0 to 1 - 0
− 100 to 300 1 0
− 100 to 300 1 0
− 100 to 300 1 0
− 100 to 300 1 0
− 100 to 300 1 0
− 100 to 300 1 0
− 100 to 300 1 0
− 100 to 300 1 0
− 100 to 300 1 0
− 100 to 300 1 30
50 to 500 10 ms 50
0 to 300 Pulse 60
80 to 300 Pulse 80
0 to 1 - 0/1
0 to 99 1 sttch 5
0 to 50 1mm 23/14
0 to 1 – 0/1
0 to 3,000 1 1,000/1,500
pulse/sec.