JUKI MEB-3200 Manuel D'utilisation page 28

NO.
Name
11
RIGHT " − " key
12
RIGHT " ＋ " key
13
PATTERN key
14
DATA key
COUNTER key
15
NEEDLE key
16
17
LOOPER key
18
LENGTH key
19
STITCHES
(Number of sttches
of parallel)
key
20 STITCHES
(Number of sttches
of eyelet)
key
SPACE
21
(Cut space)
key
22
SPACE
(Eyelet
space) key
Note 1 : When changing the set value, operate the panel in the state that the sewing LED has gone out.
Note 2 : When both the before-cut and after-cut knives are not selected (set value : "0"), the data without knife is
selected.
Note 3 : Effective / ineffective of knife operation can be selected in case of the before-cut and after-cut knives,
however, in case of the data without knife, the knife operation cannot be performed.

Descrpton
Ths key subtracts varous
data.
Ths key adds varous data.
Ths key performs dsplay
and settng of pattern No.
Ths key performs dsplay
and settng of data No.
Ths key performs dsplay
of counter.
Ths key performs dsplay
a n d s e t t  n g o f n e e d l e
thread tenson data.
Ths key performs dsplay
a n d s e t t  n g o f l o o p e r
thread tenson data.
Ths key sets the length to
be sewn.
Note 1
Ths key sets the number
of sttches of the parallel
secton.
Note 1
Ths key sets the number
of sttches of the eyelet
secton.
Note 1
Ths key sets clearance
between cloth cuttng knfe
and sewng at the parallel
secton. Note 1
Ths key sets clearance
between cloth cuttng knfe
and sewng at the eyelet
secton.
NO.
Name
23
LENGTH
(Taper bar
length) key
Note 1
STITCHES
24 (Number
of sttches
of taper bar)
key
25
OFFSET
(Taper bar
offset) key
26 MAX
(Sewng
speed) key
27
EYELET
(Eyelet speed
settng) key
28
KNIFE
(Knfe ON/
OFF)key
29
CB
(Before-cut
knfe) key
CA
30
(After-cut
knfe) key
31 SHAPE
(Knfe No.)
key
32 AUTO
(Auto
operaton)
key
33
OPEN
(Cloth
open) key
34
ADJUST
(Knfe adjust)
key
35
FUNCTION
(Functon) key
Descrpton
Ths key sets sewng length
of taper bar.
Note 1
Ths key sets the number
of sttches of taper bar.
Note 1
T h  s k e y s e t s t h e s l  p
amount of taper bar.
Note 1
Ths key performs settng
of sewng speed.
Note 1
Ths key performs settng
of reduced speed at eyelet
secton.
Note 1
Ths key sets effectve/
neffectve of knfe.
Note 3
Ths key performs data
settng of before-cut knfe.
Note 2
Ths key performs data
settng of after-cut knfe.
Note 2
Ths key selects the No. of
knd of knfe to be used.
Note 1
Ths key performs change-
o v e r o f a u t o m a t  c a n d
manual operaton modes.
The mode becomes the
one operatng wth the cloth
open mechansm opened.
The mode becomes the
one of cloth cuttng knfe
adjustment by turnng ON
the power wth ths key
held pressed.
Ths key can be changed to
optonal data settng functon
key wth the memory swtch.
At the tme of delvery
F1 : Knfe poston adjustment (No. 8)
F2 : Copy destnaton No. (No. 80)