Publicité
Les langues disponibles
Les langues disponibles
Stage 17, the deck railing, parts 17.1 - 17.7
Part No.
Description
17.1
Railing stanchion
17.2
Handrail
17.3
Split pin
17.4
Railing stanchion
17.5
Rail
17.6
Handrail
17.7
Split pin
- The previously drilled wooden board is now used as a sol-
dering jig LH to make up the railings. Push four sleeves 17.1
in the board to form railing stanchions for the forward deck
railing.
- Bend the handrail 17.2 to shape and secure it with the split
pins 17.3.
- Solder the parts together.
- Make up the second handrail in the same way.
Stage 18, the bow gun 8.8, parts 18.1 - 18.11
Part No.
Description
18.1
Plinth
18.2
Screw
18.3
Gun barrel
18.4
Muzzle plug
18.5
Gun mount, R / L
18.6
Hand-wheel
18.7
Shaft
18.8
Angle drive
18.9
Bracket
18.10
Bar
18.11
Bracket
- Apply the floor grid (sticker) to the gun plinth (F).
- Fix the plinth 18.1 to the front deck using the screw 18.2.
Apply a drop of Loctite to the screw.
- Tighten the screw to the point where the plinth is still just
free to rotate.
- Glue the gun barrel 18.3 to the muzzle plug 18.4.
- Place the gun barrel 18.3 between the gun mount compo-
nents 18.5 and glue this assembly to the plinth, taking care
not to glue the screw at the same time.
- Drill out the four hand-wheels 18.6 to 1.5 mm ø
- Fit the two shafts 18.7 in the holes of the gun components
Stage 19, the AA machine gun, parts 19.1 - 19.7
Part No.
Description
19.1
Machine gun mount
19.2
Screw
19.3
Machine gun barrel
19.4
Shoulder brace
19.5
Yoke section, R / L
19.6
Hand-wheel
19.7
Shaft
Assembly instructions
U 47
Material
Size in mm
Brass tube
2 ø x 30
Brass rod
2 ø x 190
Brass
1 ø x 15
Brass tube
2 ø x 35
Brass rod
1.2 ø x 120
Brass rod
2 ø x 160
Brass
1 ø x 15
- Position the railings on the deck and glue them in place.
- File a recess in the rear railing stanchions 17.4 to accept the
rail 17.5.
- Bend the handrail 17.6 to shape, assemble the railing com-
ponents on the soldering jig using the split pins 17.7 and sol-
der the parts together (F).
- Glue the completed railing to the deck.
Material
Size in mm
Plastic
Inj. moulded
Brass
M2 x 16
Plastic
Inj. moulded
Plastic
Inj. moulded
Plastic
Inj. moulded
Plastic
10 ø
Brass rod
1.5 ø x 12
Brass rod
1.5 ø x 8 x 12
Brass rod
1.5 ø x 18 x 22
Plastic
Inj. moulded
Brass rod
1.5 ø x 18 x 30
and glue the hand wheels in place.
- Bend the angle drive 18.8 to the shape shown and insert it
together with the two remaining hand-wheels.
- Attach the two bars 18.10 to the single-edged brackets 18.9
and glue them in the holes in the gun mount.
- Make up the two-edged brackets 18.11 taking care to pro-
duce a handed pair.
- Glue the two bars 18.10 on top of the brackets and glue
these assemblies to the gun mount.
Material
Size in mm
Plastic
Inj. moulded
Brass
M2 x 30
Plastic
Inj. moulded
Plastic
Inj. moulded
Plastic
Inj. moulded
Plastic
Inj. moulded
Brass rod
1.5 ø x 10
35
Order No.
1114
No. off
Notes
8
2
8
6
Flanged
2
2
6
No. off
Notes
1
1
1
1
1 each
4
2
2
2
4
2
No. off
Notes
1
1
1
2
1 each
1
1
Publicité
