ROBBE U 47 Notice De Montage Et D'utilisation page 26

Stage 6, installing the servos and the rear connection components, parts 6.1 - 6.15
Part No. Description
6.1 Rudder servo
6.2 Hydroplane servo
6.3 Hydroplane pushrod
6.4 Rudder pushrod
6.5 Switch pushrod
6.6 Hose
6.7 Hose clip
6.8 Bellows
VR Extension tube
6.9 Servo output arm
6.10 Connecting rod
6.11 Collet
6.12 Grubscrew
6.13 Switch
6.14 Collet
6.15 Grubscrew
- Install the servos 6.1 and 6.2 using the screws and grom-
mets supplied with them.
- Cut the three pushrods 6.3 - 6.5 to approximate length. File
one end of each rod to a slight point as this makes it easier
to fit the bellows 6.8 onto them when lubricated with a little
water (F).
- Fit pieces of silicone hose 6.6 on the pushrods 6.4 and 6.5,
bend them to the shape shown in the full-size drawings and
cut them to final length (F).
- Push the hose clips 6.7 onto the shoulders of the rear cover.
- Insert the pushrods and fit the rubber bellows 6.8 onto them
to a depth of about 10 mm.
- Fit the hose clips using the extension tubes VR. Rotate the
clips so that the ends are at the top.
- Cut the servo output arms 6.9 to length and drill them out as
shown. Connect the hydroplane pushrod 6.3 directly to the
servo output arm and fit the arm on the servo.
- Make up the connecting rod 6.10. Connect the pushrod 6.10
Stage 7, the aft hydroplane system, parts 7.1 - 7.15
Part Description
No.
7.1 Bearing bracket
7.2 Screw
7.3 Bearing rivet
7.4 Square shaft
K Block
7.5 Tiller
7.6 Collet
7.7 Grubscrew
7.8 Rear hydroplane
7.9 Collet
7.10 Grubscrew
7.11 Rear bar
7.12 Extension pushrod
7.13 Clevis
7.14 Collet
7.15 Grubscrew
Assembly instructions
U 47
Material Size in mm
—- Ready made
—- Ready made
Brass rod 2 ø x 290
Brass rod 2 ø x 240
Brass rod 2 ø x 370
Silicone 5.5 ø x 80
Steel wire Pre-formed
Rubber Ready made
Brass 2.5 ø x 70
Plastic Ready made
Brass rod 2 ø x 90
Steel 4 ø x 7 ø x 5
Steel M3 x 3
—- Ready made
Brass 2 ø 7 ø x 5
Steel M3 x 3
to the pushrod 6.4 using the servo output arm 6.9 and col-
let 6.11 fitted with the grubscrew 6.12.
- Drill a lengthwise hole in the switch lever 6.13 and tem-
porarily fit the switch on the pushrod using the two collets
6.14 / 6.15. Position the pushrod laterally as shown and
glue the switch housing to the servo plate with a little
Stabilit-Express.
- The following process should again be carried out on a flat
table top.
- Insert the base frame and engage the couplings.
- Fit the rear hull section. Insert the shafts and the shaft tem-
plate W and connect them to the couplings (F).
- Push the parts together and check alignment once more
using the string.
- Complete the glued joints between the rear hull section
and the cover by applying Stabilit-Express from inside the
rear hull section.
Material Size in mm
ABS 3
Brass M3 x 30
Brass 5 ø x 5
Brass 3 x 3 x 150
Obechi 20 x 30 x 53
Plastic Inj. moulded
Steel 4 ø x 7 ø x 5
Steel M3 x 6
Plastic Inj. moulded
Steel 4 ø x 7 ø x 5
Steel M3 x 3
Plastic Inj. moulded
Brass rod 1.5 ø x 200
Steel M2, ready made
Steel 4 ø x 7 ø x 5
Steel M3 x 3
27
Order No.
1114
No. off Notes
1 Not included
1 Not included
1
1
1
2
3
3
2 Sleeve
2 Not included
1
1
1
1 Not included
2
2
No. Notes
off
1 Die-cut, B
1 Also drilling jig
4
1
2
1
1
1
2
4
4
2
1
1
1
1