Efco AT 900 Manuel D'utilisation Et D'entretien page 29

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 43
GASOLINE
1
5
10
15
20
25
This product is powered by a 2-cycle engine and
requires pre-mixing gasoline and 2-cycle oil. Pre-
mix unleaded gasoline and 2-cycle engine oil in
a clean container approved for gasoline.
RECOMMENDED FUEL: THIS ENGINE IS
CERTIFIED TO OPERATE ON UNLEADED GASOLINE
INTENDED FOR AUTOMOTIVE USE WITH AN
OCTANE RATING OF 89 ([R + M] / 2) OR HIGHER.
Mix 2-cycle engine oil with gasoline according to
the instructions on the package.
We strongly recommend the use of 2% (1:50)
Efco - Oleo-Mac two cycle engine oil, which is
specifically formulated for all air-cooled two-
stroke engines.
The correct oil / fuel proportions shown in the
table (Fig. A) are suitable when using the
PROSINT 2 and EUROSINT 2 or an equivalent
high-quality engine oil (JASO specification FD
or ISO specification L-EGD).
CAUTION: DO NOT USE AUTOMOTIVE OIL
OR 2-CYCLE OUTBOARD OIL.
CAUTION:
- M atch your fuel purchases to your
consumption; don't buy more than you will
use in one or two months;
- Store gasoline in a tightly-closed container
in a cool, dry place.
CAUTION - For the mixture, never use a
fuel with an ethanol percentage higher than
10%; gasohol (mixture of gasoline and
ethanol) up to 10% ethanol or E10 fuel are
acceptable.
NOTE - Prepare only the quantity of mixture
required for immediate use; do not leave fuel in
the tank or a container for a long time. Were
OIL
2% - 50:1
3
(cm
)
0,02
(20)
0,10
(100)
0,20
(200)
0,30
(300)
0,40
(400)
0,50
(500)
commend the use of the additive Emak ADDITIX
A
2000 code 001000972 if the mixture is to be
stored for 12 months.
Alkylate gasoline
CAUTIONS – Alkylate fuels have different
density than normal fuel. Therefore engines,
set with normal fuel, need different H jet
regulation to avoid critical issues. For this
operation it's necessary turned at a Licensed
Service Dealer.
Filling the tank
stir the mixture well before refuelling.
Using the supplied bottle (Fig.10)
To facilitate refuelling operations, each machine
is supplied with a bottle for preparation 50:1 (2%)
two-stroke mixture.
Refer to Fig.10 and proceed as follows to prepare
one litre of mixture:
1. Fill the bottle with petrol up to position 1.
2. To prepare a 50:1 (2%) mixture add oil up to
position 2.
3. Screw the cap onto the bottle.
4. Shake the bottle for at least 30 seconds.
The mixture is now ready and can be used to
refuel the mist blower.
If you are using a petrol can to prepare the
mixture, make sure the container is clean and mix
for at least a minute to ensure the oil is properly
dissolved in the petrol. The oil percentages are
shown in the tables below.
WARNING: Follow safety instruction for
fuel handling. Always shut off engine before
fuelling. Never add fuel to a machine with a
running or hot engine. Move at least 3 m from
refuelling site before starting engine. DO NOT
SMOKE!
1. Clean surface around fuel cap to prevent
contamination.
2. Loosen fuel cap slowly.
3. Carefully pour fuel mixture into the tank.
Avoid spillage.
4. Prior to replacing the fuel cap, clean and
GB
25

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

At 9000

Table des Matières