Parkside PBKP 8000 A1 Consignes D'utilisation page 10

The noise emission values have been determined in ac-
cordance with EN ISO 3744:1995.
Noise data
Sound pressure level L
pA
Measurement uncertainty K
Sound power level L
wA
Measurement uncertainty K
Guaranteed sound power level L
If necessary, adhere to rest periods and limit the dura-
tion of work to the bare minimum.
8 Unpacking
• Open the packaging and carefully remove the prod-
uct.
• Remove the packaging material, as well as the pack-
aging and transport safety devices (if present).
• Check whether the scope of delivery is complete.
• Check the product and accessory parts for transport
damage. Immediately report any damage to the
transport company that delivered the Product. Later
claims will not be recognised.
• If possible, keep the packaging until the expiry of the
warranty period.
• Familiarise yourself with the product by means of the
operating manual before using for the first time.
• With accessories as well as wearing parts and re-
placement parts use only original parts. Spare parts
can be obtained from your specialist dealer.
• When ordering please provide our article number as
well as type and year of manufacture for the product.
WARNING
The product and the packaging material are not
children's toys!
Do not let children play with plastic bags, films or
small parts! There is a danger of choking or suf-
focating!
9 Before commissioning
WARNING
Health hazard!
Inhalation of fuel / lubricating oil vapours and exhaust
gases can cause serious damage to health, uncon-
sciousness and in extreme cases death.
– Do not breathe fuel / lubricating oil vapours and
exhaust gases.
– Operate the product outdoors only.
6 | GB / IE / NI / CY / MT
96 dB
3 dB
pA
109 dB
3 dB
wA
112 dB
wA
* = not included in the scope of delivery!
Note:
The product has a centrifugal clutch. This creates a fric-
tional connection as the speed increases by pressing the
clutch facings against the inner wall of the clutch hous-
ing due to the centrifugal force.
Check before operation
• Check all sides of the engine for oil or fuel leaks.
• Check the fuel level – the fuel tank should be at least
half-full.
• Check the condition of the air filter.
• Check the condition of the fuel lines.
• Look for signs of damage.
• Check that all protective covers are in place and all
screws, nuts and bolts are tightened.
• Ensure that the product is sufficiently ventilated.
• Make sure that the spark plug connector is attached
to the spark plug.
• The suction and pressure lines must be installed in
such a way that they do not exert any mechanical
pressure on the pump.
9.1 Installation of the suction line*
(Fig. 3)
Note:
The pump has a non-return valve which prevents the
water from flowing back into the suction line.
• The suction line* must be reinforced with rigid walls
or wire mesh.
• Do not use a hose* that is smaller than the suction
line* of the pump.
• The suction line* should only be as long as neces-
sary.
• Pumping performance is best when the pump is as
close to the surface of the water as possible and the
hoses* are short.
• A leaking suction line* will prevent the water from
being sucked in due to air ingress.
1. Insert the hose adapter (15) into the union nut (16).
2. Insert the seal (17) into the union nut (16).
3. Screw a union nut (16) onto the suction connection
(10) and tighten it firmly (8 - 10 Nm).
Make sure that the seal (17) of the union nut (16) is
in contact with the suction connection (10).
4. Attach the suction line* to the hose adapter (15) of
the suction line* with a hose clamp (18) to avoid air
leakage and loss of suction power. Use the Phillips
screwdriver on the spark plug spanner (20) to tight-
en the hose clamp (18).