Table des Matières
Publicité
!
a secco delle pompe IM, oltre a
causare il danneggiamento della
boccola interna, provoca il
surriscaldamento e la fusione degli
elementi interessati da attrito raden-
te ed il conseguente, possibile
incendio.
GB
COMMISSIONING
The installer/operator must always use
material compatible with the pumped
liquid and in accordance with the
design conditions of the pump.
WARNING: it is forbidden to use
!
1
liquids that are incompatible
with the materials of the pump
components or in an environment
where there are incompatible fluids.
In order to start-up the pump, proceed
as follows.
1 Check that the product delivery
conduit is connected.
WARNING: dry operation of IM
!
pumps, besides damaging the
internal bushing, causes
F
DÉLAIS DES ENTRETIENS COURANTS
overheating and fusion of parts
subject to horizontal friction, and
may subsequently cause a fire.
Pour garantir les rendements et les utilisations en toute sécurité,
2
les pompes IM exigent des interventions d'entretien courant qui
doivent être effectuées pendant la durée de vie de la pompe
dans le respect des délais indiqués dans le tableau.
4
5
Les délais d'intervention des entretiens courants repris dans le
tableau se réfèrent à des usages en conditions normales ; des
usages des pompes IM en conditions plus difficiles requièrent
des interventions plus fréquentes, avec un déclassement de
30% à 50% des fréquences d'intervention indiquées.
GB
STANDARD MAINTENANCE TIME-SCHEDULE
In order to guarantee performance and safe use, IM pumps
need standard maintenance operations throughout their life
span and in accordance to the time-schedule detailed in the
table.
27
The time schedule for routine maintenance shown in the table
refers to standard use and working conditions; more demanding
working conditions require more frequent operations, with a
30% to 50% more frequent interventions than that indicated.
CONTRÔLE ET/OU INTERVENTION
A - GRAISSAGE DU ROULEMENT
B - ENTRETIEN DU CIRCUIT DU PRODUIT
C - NETTOYAGE INTERNE DE LA POMPE
D - REMPLACEMENT DES JOINTS STATIQUES
E - REMPLACEMENT DE LA BAGUE D'USURE
CHECK AND/OR OPERATION
A GREASE THE BEARING
B PRODUCT CIRCUIT MAINTENANCE
C INTERNAL CLEANING OF THE PUMP
D REPLACEMENT OF STATIC SEALS
E REPLACEMENT OF THE WEARING BUSHING
WARNING: it is forbidden to use
!
2 Aprire la valvola a sfera manuale della
liquids that are incompatible
tubazione del fluido.
with the materials of the pump
components or in an environment
where there are incompatible fluids.
3 Effettuare il riempimento della vasca
rispettando i livelli MIN e MAX così
In order to start-up the pump, proceed
da invasare la pompa.
as follows.
4 Avviare il motore mediante gli apposi-
1 Check that the product delivery
ti comandi.
conduit is connected.
5 Per l'arresto della pompa agire esclu-
!
WARNING: dry operation of IM
sivamente sui comandi di arresto del
pumps, besides damaging the
motore elettrico della pompa.
internal bushing, causes
overheating and fusion of parts
ATTENZIONE: non arrestare mai
!
subject to horizontal friction, and
la pompa in funzione mediante
may subsequently cause a fire.
la chiusura della valvola a sfera di
mandata del circuito del fluido:
PERICOLO DI STALLO DELLA POM-
PA E/O DI INCENDIO DOVUTO ALLA
FUSIONE DELLA BOCCOLA CERAMI-
CA PER FUNZIONAMENTO A SECCO.
4
5
2. Open the manual ball valve of the
fluid piping;
3. Fill the tank, respecting the MIN and
MAX levels, so as to flood the
pump.
4. Start the motor with the appropriate
controls.
5. To stop the pump, only use the stop
27
controls of the pump electrical
motor.
!
WARNING: never stop a working
pump by closing the delivery
ball valve of the fluid circuit: THE
PUMP MAY STALL AND/OR A FIRE
MAY BE CAUSED BY THE FUSION
OF THE CERAMIC BUSHING DUE TO
DRY OPERATION.
3
PA E/O DI INCENDIO DOVUTO ALLA
I
2
FUSIONE DELLA BOCCOLA CERAMI-
CA PER FUNZIONAMENTO A SECCO.
!
ATTENZIONE: verificare che
durante il funzionamento non
4
5
vi si verifichi rumorosità o vibrazioni
anomale. In tal caso arrestare
immediatamente la pompa per
accertare ed eliminare le cause.
ATTENZIONE: controllare che
!
nel fluido in uscita non siano
presenti bolle di aria, nel qual caso
arrestare immediatamente la pom-
2. Open the manual ball valve of the
pa ed eliminare le cause.
fluid piping;
3. Fill the tank, respecting the MIN and
ATTENZIONE: non installare
!
MAX levels, so as to flood the
sull'aspirazione filtri che posso-
pump.
2
no causare perdite di carico.
4. Start the motor with the appropriate
3
controls.
27
5. To stop the pump, only use the stop
controls of the pump electrical
motor.
!
WARNING: never stop a working
pump by closing the delivery
ball valve of the fluid circuit: THE
PUMP MAY STALL AND/OR A FIRE
MAY BE CAUSED BY THE FUSION
OF THE CERAMIC BUSHING DUE TO
GB
DRY OPERATION.
WARNING: check that there is
!
no anomalous noise vibration
while the pump is working. If so,
ATTENTION : le manque d'entretien et/ou le non-
!
immediately stop the pump, check
respect des délais d'intervention des entretiens
and eliminate the cause.
courants, outre à déterminer la déchéance des
!
WARNING: check that there are
conditions de garantie, peut provoquer l'usure excessive
3
no air bubbles in the outlet
fluid. If so, immediately stop the
et endommagement des organes internes de la pompe
pump, check and eliminate the
et/ou du moteur, ainsi que la vérification de situations
cause.
dangereuses non imputables au fabricant.
WARNING: do not install filters
!
on the suction inlet as they may
cause pressure loss.
WARNING: failure to proceed and/or comply with
!
standard maintenance and/or its time schedule,
renders the warranty null and can excessively
wear and damage the internal parts of the pump and/or the
motor, as well as create hazardous situations, for which
the manufacturer is not to be held liable.
toutes les 100 heures
●
every 100 hours
●
25
pump.
ATTENZIONE: non installare
!
sull'aspirazione filtri che posso-
4. Start the motor with the appropriate
no causare perdite di carico.
controls.
5. To stop the pump, only use the stop
controls of the pump electrical
motor.
WARNING: never stop a working
!
pump by closing the delivery
ball valve of the fluid circuit: THE
PUMP MAY STALL AND/OR A FIRE
MAY BE CAUSED BY THE FUSION
OF THE CERAMIC BUSHING DUE TO
DRY OPERATION.
GB
WARNING: check that there is
!
B
no anomalous noise vibration
while the pump is working. If so,
A
C
immediately stop the pump, check
and eliminate the cause.
!
WARNING: check that there are
no air bubbles in the outlet
fluid. If so, immediately stop the
pump, check and eliminate the
cause.
WARNING: do not install filters
!
on the suction inlet as they may
cause pressure loss.
28
toutes les 1 000 heures
●
●
●
every 1000 hours
●
●
●
B
6 Dopo le prime due ore di funziona-
mento della pompa, e dopo averla
A
C
correttamente arrestata, bisogna:
A- verificare visivamente, che non vi
siano trafilamenti di prodotto nella
campana;
B- verificare il serraggio di tutti i
bulloni della pompa;
C- verificare la tenuta del condotto di
mandata del fluido.
Se necessario intervenire secondo
necessità per risolvere la situazione
presente.
6 After the first two hours of operation
of the pump, and after having
stopped it correctly, you must:
A. visually check that there is no
product leakage from the casing;
B. check the tightening of all bolts;
C. check the seal of the fluid
delivery conduit.
28
toutes les 1 500 heures
●
every 1500 hours
●
info@debem.it
6 Af
of
st
A.
B.
C.
Publicité
Table des Matières
