Démarrer Optimisation De Stabilité De Marche Ou Minimisation Des Masses - Hofmann geodyna OPTIMA II Mode D'emploi

Table des Matières

Publicité

Optimisation/ Weight minimisation
9.3 Start optimisation/weight minimisation
 To perform a Minimisation run correctly clamp a
complete wheel (
Optimisation run.
 For a MINIMISATION run, check that the tyre is
correctly mounted on the rim (Axial run-out test)
and that it is pumped up to the set pressure.
 Select the Vehicle Type (
 Read the rim dimension parameters (
 Launch a Measuring run.
 On the BALANCING screen press the F1 Menu key,
and then select the Optimisation item (1, Fig. 9-1).
The OPTIMISATION screen (Fig. 9-2) is displayed.
You can now start the procedure as follows.
Start weight optimisation
    
Press the F4 Menu key and then select the Start
Optimisation item (1, Fig. 9-2a).
The OPTIMSATION 1 screen (Fig. 9-4) is displayed.
Continue as described in Chapter 9.3.2.
Start weight minimisation
    
Press the F4 Menu key and then select the Start
Minimisation item (1, Fig. 9-2b).
The MINIMISATION 1 screen (Fig. 9-5) is displayed.
 Proceed from the MINIMISATION 1 item as described
in Chapter 9.3.1.
Recalling Optimisation/ Minimisation
Note:
If a previously interrupted Optimisation/Minimisation
run is in the memory, when the Optimisation item is
selected from the F1 Menu, the OPTIMISATION screen
(Fig. 9-4) is displayed.The interrupted cycle can be
restarted using the F3 Menu key. The program will
proceed from exactly the point at which is was
interrupted.
 Clamp the wheel removed previously when the
Optimisation/Minimisation run was interrupted.
    
Press the menu key F3.
The screen in which optimisation/weight minimisation was
previously interrupted is displayed.
 Proceed according to the current programme stage.
geodyna OPTIMA II
6.5) or just the rim for an
7.1.1).
7).
Optimisation / Minimisation des masses
9.3 Démarrer optimisation de stabilité de
marche ou minimisation des masses
 Bloquer correctement (
effectuer la minimisation, ou la jante uniquement pour
lancer une optimisation.
 En cas de MINIMISATION, contrôler que le pneu soit
correctement monté sur la jante (vérification
d'excentricité) et qu'il soit gonflé à la pression prescrite.
 Sélectionner le type de véhicule (
 Relever les dimensions de la jante (
 Exécuter la lancée de mesure.
 Sur l'écran EQUILIBRAGE, appuyer sur la touche de
menu F1, puis sélectionner l'option Optimisation (1,
Fig. 9-1).
L'image OPTIMISATION (Fig. 9-2) est alors affichée.
Il est maintenant possible de lancer la procédure comme suit.
Lancer l'optimisation de stabilité de masses
    
Appuyer sur la touche de menu F4, puis
sélectionner l'option Lancer l'optimisation (1, Fig.
9-2a).
L'image OPTIMISATION 1 (Fig. 9-4) est alors affichée.
Continuer comme décrit au § 9.3.2.
Lancer la minimisation des masses
    
Appuyer sur la touche de menu F4 puis sélectionner
l'option Lancer la minimisation (1, Fig. 9-2b).
L'image MINIMISATION 1 (Fig. 9-5) est alors affichée.
 Continuer depuis l'option MINIMISATION 1 comme
décrit au § 9.3.1.
Récupération de l'optimisation/minimisation
Nota Bene:
Si une optimisation/minimisation interrompue se
trouve en mémoire, l'écran OPTIMISATION (Fig. 9-4)
s'affiche lorsque l'option Optimisation est sélectionnée
dans le menu F1.A l'aide de la touche F3, il est
possible de reprendre le cycle interrompu à partir de
l'étape de programme en cours au moment de
l'interruption.
 Bloquer la roue retirée auparavant avec l'interruption
de l'optimisation/minimisation.
    
Appuyer sur la touche de menu F3.
Il sera affiché celui des écrans au cours duquel
l'optimisation de la stabilité de marche / la minimisation
des masses a été interrompue auparavant.
 Procéder selon l'étape de programme en cours.
geodyna OPTIMA II
6.5) la roue complète pour
7.1.1).
7).
209

Publicité

Table des Matières
loading

Table des Matières