Mounting The Grass Catcher Bag; Mounting The Grass Catcher Tipping Levers; Mounting The Cutting Means Assembly Lateral Safety Panels (If Fitted); Side Discharge Chute Assembly (For Models With Side Discharge Only) - GGP ITALY SPA TC 102 Série Manuel D'utilisation

4.8 MOUNTING THE GRASS
CATCHER BAG
• For TC model
1. First assemble the frame, uniting the
upper part (fig. 9.A) with the lower
part (fig. 9.B), using the nuts and bolts
supplied (fig. 9.C) as indicated.
Position the angular plates (fig.
9.D) and (fig. 9.E), respecting the
right (R⇑) left (L⇑) alignment, and
securing them to the frame using
four self-tapping screws (fig. 9.F).
2. Models with electrical tipping
function only: Mount the two rollers
(fig. 9.G) on the support pins (fig.
9.H), making sure that the catcher is
facing the support, and secure it using
elastic rings (fig. 9.I). Next, secure the
supports to the front frame (fig. 9.B)
using the nuts and bolts (fig. 9.J).
3. Insert the frame into the canvas cover
(fig. 9.K), making sure that it is positioned
correctly around the base. Attach the
various plastic profiles to the frame
tubes using a screwdriver (fig. 9.L).
4. Insert the handle (fig. 9.M) via the holes
on the cover (fig. 9.N), and secure the
resulting sub-assembly to the frame
using the screws (fig. 9.O) as indicated,
and the rear self-tapping screws (fig. 9.P).
5. Mount the strengthening cross bar
(fig. 9.Q) under the frame using the
nuts and bolts (fig. 9.R), so that the
flat part is facing the canvas. Insert
the emptying lever (fig. 9.S) into its
housing and fit the retaining screw (fig.
9.T) and associated nut (fig. 9.U).
• TS-TX-TH models
Complete the grass catcher mounting
sequence as described in the instruction
sheets supplied with the components.
4.9 MOUNTING THE GRASS
CATCHER TIPPING LEVERS
Position the lever shaft (fig. 10.A) so
that it lies in the groove in the two plates
(fig. 10.B) and secure it to the inner
part of the grass catcher bag supports
(fig. 10.C), using the nuts and bolts (fig.
10.D) supplied in accordance with the
sequence indicated in the figure.
Connect the end of the lifting piston
shaft (fig. 10.E) to the lever (fig. 10.F)
by using the pin (fig. 10.G) and mount
the two elastic rings (fig. 10.H).
Before mounting the grass catcher
bag on its support, make sure that
tipping levers move correctly.
4.10 MOUNTING THE CUTTING
MEANS ASSEMBLY LATERAL
SAFETYPANELS(IFFITTED)
Mount the safety panels (fig. 11.A) using
the screws (fig. 11.B) and nuts (fig. 11.C)
supplied, in accordance with the instructions
provided for each machine type.
4.11 SIDE DISCHARGE CHUTE
ASSEMBLY(FORMODELSWITH
SIDEDISCHARGEONLY)
1. From the inside of the side discharge
chute (fig. 12.A), fit the spring (fig.
12.B) by inserting the terminal (fig.
12.B.1) into the hole and turning it so
that both the spring (fig. 12.B) and
the terminal (fig. 12.B.2) are securely
positioned in their housings.
2. Position the side discharge chute (fig.
12.A) in line with the cutting means
assembly brackets (fig. 12.C). Using a
screwdriver, turn the second terminal (fig.
12.B.2) of the spring (fig. 12.B) to bring
it outside the side discharge chute.
3. Fit the pin (fig. 12.D) in the holes
on the brackets (fig. 12.C) and on
the side discharge chute, so that it
passes through the coils of the spring
(fig. 12.B) and the drilled end comes
out of the inner most bracket.
EN - 9