Seat Assembly; Mounting And Connecting The Battery; Mounting The Grass Catcher Supports; Removing The Grass Catcher Retaining Pawl - GGP ITALY SPA TC 102 Série Manuel D'utilisation

5. Tighten the screw (fig. 3.E) fully
using a socket wrench.
6. Replace the cap on the steering wheel (fig.
3.B) inserting it so that it clicks into place.
• Type "II" steering wheel
1. Put the machine on a flat surface
and straighten the front wheels.
2. Using a screwdriver, remove the central cap
(fig. 3.I) from the steering wheel (fig. 3.H).
3. Put the machine on a flat surface
and straighten the front wheels.
4. Fit the steering wheel (fig. 3.H) onto the
protruding shaft (fig. 3.J), rotate it so that the
spokes are aligned correctly, and then push
it so that the steering wheel hub couples
with the protruding end of the pin (fig. 3.K).
5. Secure the steering wheel using the screw
(fig. 3.L) and the elastic washer (fig. 3.M)
supplied, in the indicated sequence.
6. Tighten the screw (fig. 3.L) fully
using a socket wrench.
7. Replace the cap on the steering wheel (fig.
3.I) inserting it so that it clicks into place.

4.3 SEAT ASSEMBLY

Pull the regulator lever up (fig. 4.C) and
slide the seat (fig. 4.A) into the guide (fig.
4.B) from the steering wheel side, until
it clicks into one of the six positions.
At this point, the seat has been mounted
securely, so that it cannot be removed again
without pressing the release lever (fig. 4.D).
4.4 MOUNTING AND CONNECTING
THE BATTERY
The battery (fig. 5.A) is housed under the
seat and secured by a spring (fig. 5.B).
1. First connect the red wire (fig. 5.C) to
the positive pole (+) and then the black
wire (fig. 5.D) to the negative pole (–),
using the screws supplied as shown.
2. Mount the battery retaining spring (fig. 5.B),
making sure that the cables are routed
correctly in front of the battery, so that they
are not pinched by the spring (fig. 5.B).
IMPORTANT Always fully charge the
battery according to the instructions
in the battery booklet.
IMPORTANT To avoid tripping the electronic
board protection device, never attempt to start
the engine if the battery is not fully charged!
4.5 MOUNTING THE GRASS
CATCHER SUPPORTS
Mount the two supports (fig. 6.A) on
the rear plate (fig. 6.B), using the three
screws (fig. 6.C) supplied for each
support, as indicated, without locking
the corresponding nuts (fig. 6.D).
Fasten the upper part of the grass catcher
frame (fig. 6.E) to the supports and centre it
with respect to the rear plate (fig. 6.B).
Adjust the position of the two supports (fig.
6.F) with respect to the stop (fig. 6.G) so that,
by rotating the grass catcher frame, the stud
(fig. 6.H) fits into the housing correctly (fig.
6.I).
Check again that the frame (fig. 6.E) is
centred correctly with respect to the rear
plate (fig. 6.B) and that it rotates correctly, as
described above, then tighten the fastening
screws (fig. 6.C) and nuts (fig. 6.D).
4.6 REMOVING THE GRASS
CATCHER RETAINING PAWL
When the machine is shipped the grass
catcher retaining catch (fig. 7.A) is secured to
the rear plate by means of the hook (fig. 7.B).
This must be removed before mounting the
grass catcher bag supports and may no
longer be used.

4.7 MOUNTING THE REAR BUMPER

• Type "I" bumper
• Type "II" bumper
1. Mount the front bumper (fig. 8.A) on
the lower part of the frame (fig. 8.B)
using the four screws (fig. 8.C).
EN - 8