Ir Receiver And Manual On / Off; Ir Receiver / Function Indicator; Start-Up; Switching On - Truma Saphir comfort IR Instructions De Montage

IR receiver and manual on / off

There is an additional pushbutton on the IR receiver (m), with
which the unit can also be switched on and off without the
remote control (e.g. with a ballpoint pen).
If the unit is switched on using this pushbutton, the system is au-
tomatically reset to the factory settings (automatic mode 22 °C).

IR receiver / function indicator

LED 1
LED 2
Fig. 4
LED 1 green – illuminated – (cooling mode)
LED 1 green – flashing – (cooling mode compressor start-up)
LED 2 orange – flashing – (timer activated)

Start-up

Before switching on, be sure to check that the camp site pow-
er supply fusing is sufficient for (230 V / min. 4.2 A).
In order to prevent the power cable of the recreational vehi-
cle from overheating (minimum cross-section 3 x 2.5 mm²)
the cable drum must be fully unwound.
The remote control must always be pointed at the infra-red re-
ceiver in order to perform the individual switching commands.
Before switching on for the first time, the remote control must
be tuned to the IR receiver.
– Insert batteries (pay attention to polarity)
– Setup symbol flashes
(if symbol does not flash, perform Reset)
– Point remote control at IR receiver
– Press Setup button and hold down
– When a beep is heard from the system, release the Setup
button
The remote control is tuned to the IR receiver, the Setup sym-
bol goes off and the air conditioning system starts in circu-
lated air mode, at low fan level and with no timer set.

Switching on

Switch on the air conditioning system using the "On / Off
switch" of the remote control. The previous settings are
taken over.
The circulated air fan runs after switching on. The com-
pressor switches itself on after no more than 3 minutes,
and the green LED (cooling) flashes.

Temperature

If necessary, use the "Temperature selection buttons" to
set the required room temperature with "+" and "–".

Mode

Select the required operating mode by pressing the "MODE"
button one or more times.
– Cooling
– Automatic
– Circulated air
When the room temperature that was selected using the re-
mote control is reached in cooling mode, the compressor
switches off and the green LED in the IR receiver goes off. The
circulated air fan continues to run in order to provide ventila-
tion. If the room temperature setting is exceeded, the device
automatically reverts to cooling mode.
In automatic mode, the fan level is selected automatically
depending on the room temperature.
In circulated air mode, the interior air is recirculated and
cleaned by the filters. No LED's illuminate in the IR receiver.

Fan

Select the required fan level by pressing the "Fan level" but-
ton one or more times.
m
Fan level (not functional in automatic mode):
– low
– medium
– high
Sleep function
In "sleep function" (cooling mode only) the fan operates at
slow speed and therefore extremely quietly.

Switching off

To switch off, press the "On / Off switch" on the remote
control. The remote control and the device are switched off.

Time

Press "Time selection button" and set current time using
the "Time setting" buttons.
The time always appears on the display.
The time must be reset after changing the batteries or after a
daylight saving time change.

Timer ON / OFF

The On / Off time of the air conditioning system can be set in
advance for a minimum of 1 hour to a maximum of 15 hours,
starting from the current time, using the integrated timer.
The device must be switched on using the remote control in
order to program it.
Set required operating mode and room temperature.
Then select TIMER ON or TIMER OFF using the "TIMER
selection buttons". Set the required On / Off time using the
"Time setting" buttons (1 hour to 15 hours) and confirm
with TIMER ON or TIMER OFF. Orange LED flashes.
Pressing the relevant timer button again deactivates the timer
function.

Reset

Resets the settings of the remote control to the factory set-
tings when pressed using a ballpoint pen, for example. Setup
symbol flashes. Remote control settings set to "Circulated
air", fan level low, no timer set.

Resend

The previous settings are resent.
15