Clearing The Remote Controls And All Settings; Clearing Memorised Remote Controls - Fig; Clearing All Settings - Fig; Locking The Programming Buttons - Fig - SOMFY DEXXO SMART io Manuel D'installation

DEXXO SMART io
8.2.3. Function of the 3-button remote control buttons
Function
Complete opening Stop
Comp.
open
Comp. Complete opening If the door is
open
Aux 230 V Aux. output ON
Integrated ON
lighting
9. CLEARING THE REMOTE CONTROLS
AND ALL SETTINGS

9.1. Clearing memorised remote controls - Fig. 37

Press the "PROG" button for 7 s until the "PROG" indicator light flashes.
Causes all stored remote controls to be cleared.

9.2. Clearing all settings - Fig. 38

Press the "SET" button for 7 seconds until the "POWER" indicator light
flashes quickly.
Clears the auto-programming and resets the default values for all
parameters.
10. LOCKING
BUTTONS FIG. 39
Warning
The keypad must be locked to ensure the safety of the users.
Failure to follow this instruction may result in serious injury, e.g.
due to crushing by the door.
Press the "SET", "+" and "-" buttons together.
The programming (auto-programming, parameter setting) is locked. The
parameter setting indicator lights come on when the programming button
is pressed.
To access the programming again, repeat the same procedure.

11. DIAGNOSTIC AND REPAIRS

11.1. Diagnostics

Meaning
POWER indicator
The first time the unit is
switched on, program-
ming is not carried out
Programming in pro-
gress
Electronic fault
Motor thermal cut-out
Other fault
Programming complete
©
Copyright 2018 SOMFY ACTIVITES SA. All rights reserved.
my
Complete closing
Complete closing
closed or open
partial opening
Otherwise
stop
Aux. output OFF
OFF
THE PROGRAMMING
Action
Perform quick commissioning of the
motorisation.
Wait until programming is complete
Switch the power supply off, wait about
5 min. then switch the power supply
back on.
Contact Somfy technical assistance.
Photoelectric cells indicator light
Normal operation
Detection in progress
Auto-test in progress
Permanent fault
Gate contact indicator light
Normal operation
Detection in progress
Auto-test in progress
Permanent fault
Wired control indicator light
No wired control
activated
Activated wired control
Indicator lights (13 to 16)
Short circuit on acces-
sories wired input
Parameter setting indicator lights
Locking/unlocking the
programming buttons
PROG indicator light
No radio reception
when a button is
pressed on the remote
control
Radio control received
but no action on the
actuator
Once detection is complete, the indica-
tor light goes out.
Once the auto-test is complete, the
indicator light goes out.
Check the alignment and wiring of the
cells
A er 3 min., the wired control input
(terminals 12 and 13) allows the door to
be controlled in dead-man mode.
Once detection is complete (gate open),
the indicator light goes out.
Once the auto-test is complete, the
indicator light goes out.
Check the closure of the gate and the
gate contact wiring.
A er 3 min., the wired control input
(terminals 12 and 13) allows the door to
be controlled in dead-man mode.
Mechanically check that the control
point is not blocked. If the control point
is not blocked, disconnect the control
point. If the indicator light goes out,
check the wiring.
Check the wiring of the accessories.
If the 4 indicator lights continue to
flash, remove the orange (5-6), black
(7 to 9) and green (12 to 18) terminals
successively to identify the cause of the
short circuit. Indicator lights can be lit
constantly red to indicate a fault on the
terminal removed.
If the 4 indicator lights continue to flash,
contact Somfy technical assistance.
If all the parameter setting indicator
lights flash when a programming button
is pressed, the keyboard is locked.
Unlock the keyboard (see section 10

Locking the programming buttons - Fig.

39)
• Check if the remote control button has
been programmed.
• Check that the remote control is
equipped with io-homecontrol radio
technology.
• Check the remote control batteries.
• Check the other indicator lights to see
if there is another fault.
• The control is not operational from this
position.
• The button is memorised for function
other than opening/closing the garage
door (for example controlling the
auxiliary output)
EN
9