Product Description; Composition - Fig; Description Of The Circuit Board - Fig; Field Of Application - Fig - SOMFY DEXXO SMART io Manuel D'installation

EN

2. PRODUCT DESCRIPTION

2.1. Composition - Fig. 1

No. Qty
1 1 Motor head
2 1 Motor head cover
3 1 Integrated lighting cover
4 1 Lintel bracket
5 1 Door bracket
6 2 Ceiling mounting bracket
7 2 Motor head mounting bracket
8 1 Manual back release device
9 1 Connecting arm
10 1 End limit stop
11 4 Chain bearing
12 1 Power supply cable
13 4 Screw H M8x16
14 4 H M8x12 screw and washer
15 6 HU8 nut
16 2 Sha
17 2 Circlips
19 4 Thread-forming screws Ø 4x8
20 2 Screw for plastic, Ø 3.5x12
21a 1 Single unit rail
21b 1 2-part rail
21b1 1 Sleeve
21b2 4 Thread-forming screws Ø 4x8
22 2 HM8 self-locking nut
23 2 Bracket
24 1 Spacer
25 2 Remote control*
* The model and number of remote controls may vary depending on the pack.

2.2. Description of the circuit board - Fig. 2

Off
Permanently lit
No. Description
1 Power indicator
2 PROG indicator light
3 PROG button
4 SET button
4
Description
Slow flashing
Rapid flashing
Very rapid flashing
Comments
: First time the unit is switched on,
programming not carried out
: Programming in progress
: Programming complete
: Electronic fault (motor thermal
cut-out, etc.)
: radio reception
: Awaiting memorisation of a radio
control point
Radio control points memorised/cleared
Selecting the operating mode
No. Description
5 - button
6 + button
7 Parameter setting
indicator lights
8 Removable terminal
block
9 Removable terminal
block
10 Removable terminal
block
11 9.6 V low-voltage
power supply input
12 Removable terminal
block
13 Cell indicator light
14 Not used
15 Gate contact
indicator light
16 Wired control
indicator light
17 Integrated lighting

2.3. Field of application - Fig. 3

This motorisation is exclusively designed to equip a garage door for
residential use of the following types:
A: Up-and-over door
B: Sectional door
C: Side door
See description of parameter Px in section 7 Advanced parameter setting
to select the type of door.
Optimising the installation
For maximum door heights, the motor travel can be optimised:
• By mounting the motor head at 90° (Fig. 7-
• By fixing the lintel yoke to the ceiling, setting it back a maximum of
200 mm in relation to the lintel (Fig. 5-
• By cutting the connecting arm (Fig. 11).

3. INSTALLATION

Attention
If the garage door is the sole means of access to the garage, install
an external back release device (ref. 9012961 or ref. 9012962).
The position in which the motorisation will be fitted must allow for safe
and easy manual release of the product.
DEXXO SMART io
Comments
Before auto-programming, close the
door by keeping the button depressed
Interrupts auto-programming
While setting the parameters, modifies
the value of a setting
Before auto-programming, open the door
by keeping the button depressed
Interrupts auto-programming
While setting the parameters, modifies
the value of a setting
P0: Operating mode
P1: Garage door speed
P2: Slowdown zone
P3: Obstacle detection sensitivity
P4: Photoelectric cells
Px: Type of door
230 V power supply
Auxiliary output
Photoelectric cells and orange light
Compatible with 9.6 V batteries
Wired control point, photoelectric cells,
gate contact, remote antenna
: Normal operation
: Detection in progress
Auto-test in progress
Permanent fault
: Control activated
: Control activated
).
)
©
Copyright 2018 SOMFY ACTIVITES SA. All rights reserved.