Programming The Remote Controls; Memorising The Keygo Io Remote Controls; Memorising 3-Button Remote Controls - SOMFY DEXXO SMART io Manuel D'installation

EN
P2
Closing slowdown zone
1: None
Values
2: Short (approx. 20 cm)
3: Long
Comments If the parameter is modified, you are advised to perform
auto-programming again.
Warning
If the setting is changed, the installer must check
that the obstacle detection system complies with
appendix A of standard EN 12 453.
Failure to follow this instruction may result in
serious injury, e.g. due to crushing by the door.
P3 Obstacle detection sensitivity
Values 1: Very weak
2: Weak
3: Standard
4: Maximum
Comments If the parameter is modified, you are advised to per-
form auto-programming again.
Warning
If the setting is changed, the installer must check
that the obstacle detection system complies with
appendix A of standard EN 12 453.
Failure to follow this instruction may result in
serious injury, e.g. due to crushing by the door.
P4 Photoelectric cells
Values 1: Active
2: BUS
3: Active with auto-test via power supply switching
4: Inactive
Comments 1: safety device without auto-test; it is essential to
check that it is operating correctly every 6 months.
2: bus cells application.
3: the auto-test is run on the device for each operating
cycle via power supply switching.
4: the safety input is not taken into account.
Warning
If P4 = 4, the motorisation cannot be operated
in automatic mode and in-view control of the
motorisation is mandatory.
Px Type of door
Values 1: Sectional
2: Side
3: Up and over
Attention
If the parameter is modified a er auto-
programming, the motorisation returns to
non-configured mode. Auto-programming must
be performed again.
8

8. PROGRAMMING THE REMOTE CONTROLS

8.1. Memorising the Keygo io remote controls

8.1.1. Via the programming interface
1) Press the "PROG" button for 2 s.
The integrated lighting and "PROG" indicator light are lit constantly.
Pressing "PROG" again allows you to memorise the next function
(partial opening, Aux 230 V output control, integrated lighting control).
2) Briefly press the outer le and right buttons on the remote control
together.
3) Briefly press the button selected to control the function (complete
opening, partial opening, Aux 230 V output control, integrated lighting
control).
Complete opening control - Fig. 17
Partial opening control - Fig. 31
Aux 230 V output control - Fig. 32
Integrated lighting control - Fig. 33
8.1.2. By copying a previously memorised Keygo io
remote control - Fig. 34
This operation is used to copy the programming from a previously
memorised remote control button.
1) Press the outer le and right buttons on the previously memorised
remote control simultaneously until the indicator light flashes.
2) Press and hold the button to be copied on the previously memorised
remote control for 2 seconds.
3) Briefly press the outer le and right buttons on the new remote control
together.
4) Briefly press the selected button to actuate the motorisation on the
new remote control.
Key:
Keygo io A = "source" remote control already memorised
Keygo io B = "target" remote control to be memorised

8.2. Memorising 3-button remote controls

8.2.1. Via the programming interface - Fig. 35
1) Press the "PROG" button for 2 s.
The integrated lighting and "PROG" indicator light are lit constantly.
Pressing "PROG" again allows you to memorise the next function
(partial opening, Aux 230 V output control, integrated lighting control).
2) Press "PROG" at the rear of the 3-button remote control to memorise
the function.
The integrated lighting and "PROG" indicator light flash for 5 s.
8.2.2. By copying a previously memorised 3-button
mono-directional io remote control - Fig. 36
Key:
A = "source" remote control already memorised
B = "target" remote control to be memorised
DEXXO SMART io
©
Copyright 2018 SOMFY ACTIVITES SA. All rights reserved.