Publicité
Les langues disponibles
Les langues disponibles
TECHNICAL SPECIFICATIONS OF PRODUCT COMPONENTS
WS200W is manufactured by NICE S.p.a. (prov. of Treviso – Italy). Nice S.p.a., in order to improve its products, reserves the right to modify their technical characteristics
at any time without prior notice. In any case, the manufacturer guarantees their functionality and fitness for the intended purposes.
Note: all the technical characteristics refer to a temperature of 20°C.
Model
Type
Technology adopted
Peak thrust
Nominal torque
Speed (no load)
Nominal torque speed
Maximum cycles frequency
Maximum continuous cycle time
Operating limits
Power input
Nominal absorbed power
Nominal absorbed current
Emergency power supply
"OPEN" input
"STOP" input
Radio Antenna input
Maximum cable length
Ambient operating
temperature
Use in acid, saline or potentially
explosive atmospheres
Mounting
Protection rating
Dimensions / weight
Remote control compatibility
Memorisable GTX4 transmitters
Range of the GTX4 transmitters
Programmable functions
Self-programming functions
Radio protocol
Radio communication
Installable wireless accessories
Installable PH100W photocells
WS100WCK
Electromechanical gearmotor for automation of automatic gates and doors with incorporated
command control unit, complete with radio receiver for "GTX4" transmitters.
24Vdc motor, reducer with helical gears; mechanical release.
A transformer inside the motor, but separate from the control unit, reduces the mains voltage to the
nominal 24 V
The structural features make it suitable for use on gates with a weight of up to 150kg and a leaf
length of up to 2.2 m. Opening angle of 110°
230 V (+10% -10%) 50/60Hz
140 W; at peak the power is 240 W for a
maximum duration of 2s
-
For normally open contacts (the closing of the contact causes the "OPEN" command)
For normally closed or normally open contacts and/or for constant resistance of 8.2 KΩ, or normally
closed contacts with self-recognition of the "normal" state (any variation from the memorised status
50Ω for RG58 or similar type of cable
Mains power supply: 30 m; inputs/outputs: 20 m with antenna cable preferably shorter than 5m
(observe the warnings regarding minimum gauge and type of cables)
On a horizontal plane using the appropriate mounting plate
237 x 155 h 290 mm / 7 kg
From 50m to 100m. This range can vary if there are obstacles or electromagnetic disturbances, and is
affected by the position of the receiving aerial incorporated in the flasher.
"Cycle" or "Complete cycle" (automatic closure) functionality
Pause time during "complete cycle", selectable from 10, 20, 40, 80 seconds
Partial opening type selectable in 4 modes
Obstacle detection system sensitivity, 4 selectable levels
"OPEN" command functionality selectable in 4 modes
Open input configuration on the control unit: open or pedestrian opening
Motors discharge on closure selectable from 8 levels
Motors discharge on opening selectable from 8 levels
Autodetection of Power&Free radio System from Mhouse devices
Auto-recognition of the type of "STOP" device (NO or NC contact or 8.2 KΩ resistance)
Recognition of the opening angle for each motor
Automation recognition with 1 or 2 motors
High security; compatible with the Power&Free System radio technology from Mhouse
Bidirectional, on 7 channels in band 868 MHz.
voltage used in all of the automation system.
150 Nm
50 Nm
1.7 RPM
1.4 RPM
20 cycles/hour at 50°C
5 minutes
1.9 A, at peak power the maximum current is
3.8 A for a maximum duration of 2 s
Provision for "PR3" buffer battery
causes the "STOP" command)
-20 ÷ 50°C
NO
IP54
237 x 155 h 290 mm / 6.2 kg
Up to 256 if memorised in mode 1
"Slow" or "fast" motors speed
Maximum 20 units
Maximum 6 pairs
WS100SK
24 Vdc
English – 31
Publicité
