Publicité
Les langues disponibles
Les langues disponibles
(*) Note - If the indicator colour is red, one of the following problems may be identified:
1) The maximum number of daily manoeuvres has been exceeded for a long period.
2) The battery is old and should be replaced.
3) The solar cell used as a solar charger is damaged.
4) The device does not receive sunlight and consequently cannot charge the battery.
If the battery is fully charged the led colour is green; otherwise it is red
(**) Note - There are 10 flash frequencies which indicate the power of the received IR signal
LED "A"
Off
1 fast red flash
each second
2 fast red
flashes + pause for 1 second
2 fast green
flashes + pause for 1 second
1 fast green flash followed by
1 fast red flash + 1 second
pause
1 flash per second, green on
the transmitter
(*) Note - If the indicator colour is red, one of the following problems may be
identified:
1) The maximum number of daily manoeuvres has been exceeded for a long
period. - 2) The battery is old and should be replaced. - 3) The solar cell used as
RADIO LEDs
STATUS
led LED B1 off
The automation is in test phase or in stand by;
led LED B2 off
bad quality of radio signal received from wireless
led LED B3 off
device
led LED B1 on
The automation is in test phase; poor quality of
led LED B2 off
radio signal received from wireless device
led LED B3 off
led LED B1 on
The automation is in test phase; good quality of
led LED B2 on
radio signal received from wireless device
led LED B3 off
led LED B1 on
The automation is in test phase; optimum quality
led LED B2 on
of radio signal received from wireless device
led LED B3 on
led LED B1 off
Automation in movement and the solar panel is
led LED B2 one quick
charging the device batteries
flash every 2 seconds (*)
led LED B3 on
(*) these indicators are seen only during the wireless network test phase (see paragraph 8.2 – Wireless devices test)
B1 = MINIMUM signal level - B2 = MEDIUM signal level - B3 = MAXIMUM signal level
TABLE 17 (FL100W)
STATUS
Indicator with batteries inserted: the device is
not powered or is faulty
Indication resulting from the insertion of the
battery or the pressure of the key; the device
is not paired with any system (factory condi-
tion)
Indication resulting from the insertion of the
battery or the pressure of the key; the device
is not part of a network, and the procedure for
its installation has been activated and device
is waiting to be recognised by a control unit;
this procedure is activated when you insert
the battery in the device or by pressing the
keypad; it has a duration of 10 seconds from
battery insertion or from the last press of the
button, after which it deactivates automatically
if no control unit has requested its address
Indication following battery insertion when
the automation is stopped; the device is
paired with a system and is communicating
correctly with the control unit
Indication following battery insertion when the
automation is stopped; the device is paired
with a system but the control unit does not
communicate (could be switched off)
The automation is moving or in test
TABLE 18 (PH100W - FL100W)
ACTION
Check that the battery is inserted with the correct polarity; if it is
correct check the battery charge; if the battery voltage meas-
ure is less than 1V the battery is empty; if the battery is charged
it is likely that the photocell is broken.
Normal operation; the photocell is ready to be recognised by
the "CL9WKA" control unit.
Normal operation; if you want the device in question to be add-
ed to the system, activate the device recognition procedure on
the "CL9WKA" control unit.
Normal operation
Check that the automation is actually stopped, that there is no
testing procedure in progress, and that it is powered and not in
stand-by; if the previous tests are positive check the quality of
the radio signal received from the device
Normal operation; if the indicator colour is red, see note (*)
a solar charger is damaged. - 4) The device does not receive sunlight and conse-
quently cannot charge the battery.
If the battery is fully charged the led colour is green; otherwise it is red.
ACTION
Insufficient radio communication; search for a better position for
the device
Limited radio communication; if possible, search for a better
position for the device
Normal operation
Normal operation
Normal operation
English – 27
Publicité
