Publicité
Les langues disponibles
Les langues disponibles
automatically.
10.4.2 - Mode 2 memorisation
With memorisation of the radio transmitter in Mode 2, each key can be
associated with any of the commands listed in Table 14.
In Mode 2 each key requires its own memorisation phase.
01. If the transmitter to be memorised is already memorised (this is the
case with the supplied transmitters that are already stored in mode
I) you must first delete the transmitter by performing the procedure
described in: "10.4.4 - Deleting a radio transmitter".
02. Press P2 (fig. 42) on the control unit, the same number of times as
your desired command, as shown in Table 14 (e.g. 3 times for the
"Open Only" command)
.
03. Check that LED P2 (fig. 42) emits a number of quick flashes which
1 time
"Open" command
2 times
"Pedestrian opening" command
3 times
"Open only" command
4 times
"Close only" command
5 times
"Stop" command
6 times
"Apartment block open" command
7 times
"High priority open" command
8 times
"Pedestrian opening 2" command
9 times
"Pedestrian opening 3" command
10 times
"Open + lock automation" command
11 times
"Close + lock automation" command
12 times
"Lock automation" command
13 times
"Release automation" command
10.4.3 - "Remote" memorisation
You can store a new radio transmitter in the control unit, without pressing
its keys directly. A previously memorised and operational "OLD" trans-
mitter must be available. The "NEW" radio transmitter to be stored will
"inherit" the characteristics of the OLD one; that is, if the OLD radio trans-
mitter is memorised in mode 1, the NEW will be memorised in mode 1;
in this case, during the programming phase, any key can be pressed
on either of the two transmitters. If, on the other hand, the OLD radio
transmitter is memorised in Mode 2, you must press the key with the
command you want on the OLD transmitter, and on the NEW, the key to
which you want to associate that command.
Holding the two transmitters, position yourself within the operating range
of the automation and perform the following operations:
01. Press the key on the NEW radio transmitter and hold it down for at
least 5s, then release it.
02. Press the button on the OLD radio transmitter 3 times slowly.
03. Press the key on the NEW radio transmitter once slowly.
At this point, the NEW radio transmitter will be recognised by the control
unit, and take on the characteristics that the OLD one had.
If there are other transmitters to memorise, repeat all the above steps for
each new transmitter.
10.4.4 - Deleting a radio transmitter
If you have available only one radio transmitter, use this operation to
delete it.
If the transmitter is memorised in Mode 1, one deletion phase is sufficient
and at point 3 you may press any key. If the transmitter is stored in mode
2, a deletion phase is required for each memorised key.
01. Press the P2 key (fig. 42) on the control unit and hold it down.
02. Wait until the LED P2 (fig. 42) lights up, within three seconds.
03. Press the key of the radio transmitter to be deleted for at least three
seconds. If cancellation was successful the LED P2 will flash quick-
ly five times. If LED P2 emits 1 slow flash, the deletion phase was
24 – English
are equal to the selected command.
04. Within 10 seconds press the desired button on the transmitter to be
memorised, holding it down for at least 2 seconds. If the procedure
was memorised correctly, the P2 LED will flash slowly 3 times.
05. If there are other transmitters to memorise for the same command
type, repeat step 03 within another 10 seconds; otherwise, the
memorisation phase will stop automatically.
TABLE 14
Commands the automation as described in table 3 (Open function)
Causes partial opening of one or two leaves as described in table 3
(Pedestrian Opening)
Causes the leaves to open (open - stop - open etc.)
Causes the leaves to close (close - stop - close etc.)
Halts the manoeuvre
The command has no effect on opening, when closing the command causes
the movement to reverse, that is, opens the leaves
Works also when the automation is locked
Causes partial opening of leaf M2, equal to halfway
Causes partial opening of both the leaves, equal to halfway
Causes an opening manoeuvre and when this is complete, the automation is locked;
the control unit will not accept any command other than "High priority open" and
"Release" of the automation
Causes a closure manoeuvre and when this is complete, the automation is locked;
the control unit will not accept any command other than "High priority open" and
"Release" of the automation
Causes a halt of the manoeuvre and locks the automation; the control unit will not
accept any command other than "High priority open" and "Release" of the automation.
Causes automation release and reset to normal operation
unsuccessful because the transmitter is not memorised.
04. If there are other transmitters to delete, keeping P2 depressed,
repeat step 3 within another 10 seconds; otherwise, the deletion
phase will stop automatically.
10.4.5 - Deleting all memorised radio transmitters
This operation deletes all memorised transmitters.
01. Press the P2 key (fig. 42) on the control unit and hold it down.
02. Wait until the P2 LED (fig. 42) lights up, then wait until it goes off,
then wait until it has flashed 3 times.
03. Release P2 exactly during the third flash.
04. Wait for around 4s for the deletion phase to finish; during this time
the LED P2 will flash very quickly.
If the procedure is successful, after a few moments the P2 LED will flash
slowly 5 times.
10.4.6 - Digital selector switch DS1 memorisation and deletion
Mode 1 memorisation – with this memorisation, the commands that can
be sent by pressing the A, B or C buttons on the DS1 selector switch are:
- key A - "OPEN" command,
- key B - "Pedestrian Opening" command,
- key C - "Open Only".
To memorise DS1:
01. Press P2 (fig. 42) for at least 3 s. When the LED P2 lights up, release
the key.
02. Within 10 s, type in the factory combination 11 (or the secret combi-
nation, if the factory combination has been changed), and press any
of the keys A, B or C on the DS1 selector switch for at least 3 s.
If the procedure was memorised correctly, the P2 LED will flash 3
times.
03. If there are other selector switches to memorise, repeat step 2 within
another 10 seconds; otherwise, the memorisation will stop automati-
cally.
Publicité
