Scope Of Delivery; Description And Working Principle; Product Information; Function - salmson NOLH Installation Et Mise En Service

ENGLISH
Pump assembled on grouted cast iron base frame :
Forces : F x [1,5 – (12,5/Flange DN)]
Moments : M x (1 + Flange DN/250)
Material Coefficient Stainless steel / FGL Cast Iron :
C = 1,536 applied on forces and moments
Temperature correction for temperature > 110°C :
C = E / E
tm 20b
With E : material modulus of elasticity at 20°C and E
20b
temperature.
Assembly on cast iron base frame :
Discharge z axis :
F
F F F
y z x
(N) (N) (N) (N)
32 340 420 360 650
40 400 500 440 780
50 540 660 600 1040
65 680 840 740 1310
80 820 1000 900 1580
100 1080 1340 1200 2100
125 1280 1580 1420 2480
150 1620 2000 1800 3140
200 2160 2680 2400 4200
250 2700 3340 2980 5230
300 3220 4000 3580 6260
Suction x axis :
F
F F F
y z x
(N) (N) (N)
(N)
50 600 540 660 1040
65 740 680 840 1310
80 900 820 1000 1580
100 1200 1080 1340 2100
125 1420 1280 1580 2480
150 1800 1620 2000 3140
200 2400 2160 2680 4200
250 2980 2700 3340 5230
300 3580 3220 4000 6260
350 4180 3760 4660 7300
Assembly on grouted cast iron base frame :
Discharge z axis :
F
F F F
y z x
(N) (N) (N) (N)
32 380 470 400 720
40 480 590 520 920
50 680 830 750 1300
65 890 1100 970 1710
80 1100 1340 1210 2120
100 1490 1840 1650 2880
125 1790 2210 1990 3470
150 2300 2830 2550 4450
200 3110 3850 3450 6030
250 3920 4840 4320 7580
300 4700 5830 5220 9130
All manuals and user guides at all-guides.com
at calculation
tm
M
M M M
y z x
(N.m) (N.m) (N.m) (N.m)
300 340 440 630
360 420 520 760
400 460 560 830
440 480 600 890
460 520 640 940
500 580 700 1040
600 760 840 1280
700 820 1000 1470
920 1060 1300 1910
1260 1460 1780 2620
1720 1980 2420 3570
M
M M M
y z x
(N.m) (N.m) (N.m)
N.m)
400 460 560 830
440 480 600 890
460 520 640 940
500 580 700 1040
600 760 840 1280
700 820 1000 1470
920 1060 1300 1910
1260 1460 1780 2620
1720 1980 2420 3570
2200 2540 3100 4570
M
M M M
y z x
(N.m) (N.m) (N.m) (N.m)
340 380 500 710
420 490 600 880
480 550 670 990
550 600 760 1120
610 690 840 1250
700 810 980 1450
900 1140 1260 1920
1120 1310 1600 2350
1660 1910 2340 3440
2520 2920 3560 5250
3780 4360 5320 7850
Suction x axis :
F F F
y z x
(N) (N) (N)
50 750 680 830
65 970 890 1100
80 1210 1100 1340
100 1650 1490 1840
125 1990 1790 2210
150 2550 2300 2830
200 3450 3110 3850
250 4320 3920 4840
300 5220 4700 5830
350 6120 5510 6820
5.2.7 SCOPE OF DELIVERY
Pump can be delivered as a complete pump set including electrical
motor, flexible coupling, coupling guard and baseplate. It can be also
delivered without one of those parts. A CE integration certificate is then
supplied.
This instructions and operating manual is part of the pump supply and
should be delivered attached to the pump. If not, ask SALMSON
Customer department to get it.
ATEX pumps may be delivered with specific instrumentation. Refer
to pump technical datasheet or to acknowledgment of order to
know exhaustive scope of supply.
6 DESCRIPTION AND WORKING PRINCIPLE
6.1 PRODUCT INFORMATION
NOLH pump is a single stage PN16 volute casing pump designed for
horizontal installation. Hydraulic characteristics and dimensions meet
EN733 requirements. Its mechanical design is according to ISO5199.
The back pull‐out design of the ball bearing assembly permits
dismantling of the impeller while suction and discharge lines are
fastened to casing flanges.
If a coupling spacer is used the motor won't have to be moved rearward
during maintenance operation.
This pump is designed to handle clear or slightly turbid fluids with non
particle content.
Foreign matter can occasionally pass through the pump but their size
should be limited to 3mm (depending on pump size) but pump lifetime
will be shortened.
6.2 FUNCTION
NOLH pump is a centrifugal pump with axial inlet and radial outlet.
Depending on required discharge pressure the pump speed is 1450 or
2900 RPM.
An impeller turns inside the pump casing (direction of rotation is
clockwise seen from drive end). The rotation movement is transmitted
to the fluid that is driven to the vanes and then pumped to the discharge
flange where it leaves the pump. In the flow passage of the pump casing
the kinetic energy of the fluid is converted into pressure energy.
NOLH pumps are not self‐priming pumps. Suction line and pump casing
should be completely filled with liquid before pump start.
When necessary or when a maximum pumping efficiency is required
several possibilities are offered to adapt capacity/pressure.
Modification of the system hydraulic characteristics :
A regulating valve is added at the discharge side of the pump. The
hydraulic loss can be adjusted and so the pump duty point.
Modification of pump characteristics :
Use of a frequency inverter gives the possibility to adjust pump speed.
The pump hydraulic curve is modified to reach required duty point but
impeller diameter is unchanged.
10
F M
M M M
y z x
(N) (N.m) (N.m) (N.m) N.m)
1300 480 550 670 990
1710 550 600 760 1120
2120 610 690 840 1250
2880 700 810 980 1450
3470 900 1140 1260 1920
4450 1120 1310 1600 2350
6030 1660 1910 2340 3440
7580 2520 2920 3560 5250
9130 3780 4360 5320 7850
10690 5280 6100 7440 10970