DJO Global ARTROMOT-SP3 Mode D'emploi page 33

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 41
well as two boxes with the selected
percentages for motor A and motor B
stop positions.
The circle appears in a box.
– Activate the function by pressing the
„+" key (plus). Deactivate the function
by pressing the „-" key (minus). In this
case it is not possible to activate/
deactive the function by pressing the
parameter key again.
– A check mark appears in the circle
which means that the function is
active.
– Press the parameter key for the
isolation program to select the upper
number field where you enter the
stop position for motor A.
– To modify the value, press the „+"
(plus) or „-" (minus) key.
Select 75%, for example.
– Press the parameter key again to se-
lect the lower number field where you
enter the stop position for motor B.
– To modify the value, press the „+"
(plus) or „-" (minus) key.
Select 25%, for example.
– Save the programmed values by
pressing the STOP key, then press the
START key to begin the treatment.
This is what happens:
Dorsal extension / plantar flexion is
treated ten times first (motor A). Motor B
is positioned at 25% of the programmed
range of motion for inversion and eversion.
Subsequently, inversion / eversion is
treated ten times (motor B). Motor A is po-
sitioned at 75% of the programmed range
of motion for dorsal extension and plantar
flexion.
Note!
The percentage values can be modi-
fied only when the special function is
enabled (check mark).
dorsal extension / plantar flexion
therapy documentation
ARTROMOT®-SP Comfort devices
with patient chip card have a special
documentation function which provides
a log of all therapy sessions.
The carriage run times as well as the
range of motion of the sessions are
recorded.
The collected data are presented graph-
ically in the form of a coordinate system
(X-axis = range of motion / Y-axis =
time) where the upper curve illustrates
the trend of the dorsal extension move-
ment and the lower curve the trend of
the plantar flexion movement.
inversion / eversion therapy
documentation
ARTROMOT®-SP Comfort devices with
patient chip card have a special docu-
mentation function which provides a log
of all therapy sessions.
The carriage run times as well as the
range of motion of the sessions are
recorded.
The collected data are presented graph-
ically in the form of a coordinate system
(X-axis = range of motion / Y-axis =
time) where the upper curve illustrates
the trend of the eversion movement and
the lower curve the trend of the inver-
sion movement.
LEVEL :
stretching in dorsal extension
With the special "stretching in dorsal
extension" function the carriage gently
stretches the joint by bending the foot
upward.
Starting at the middle position the car-
riage will first move to the programmed
plantar flexion value and then to the
programmed dorsal extension value.
Subsequently the carriage reverses 5°
towards plantar flexion and then moves
very slowly back again to the pro-
grammed dorsal extension value (display
). After that it attempts to attain
another 5 °, moving even slower than
before (display
).
If a high resistance toward the ad-
ditional 5 ° is sensed, the reverse on
load function is automatically activated
and the carriage moves in the opposite
direction.
This stretch cycle is repeated ten times.
After that the carriage moves to the
programmed maximum plantar flexion
value and restarts the dorsal extension
stretch cycle.
default setting: disabled
Note!
– If a pause is programmed when you
enable the function, the carriage will
stop for the duration of the pause
each time the maximum stretching
value is attained.
– Enabling the stretching in dorsal
extension function automatically
disables motor B. The only move-
ment performed is dorsal extension /
plantar flexion.
– It is not possible to combine a
second stretching function with the
special function „stretching in dorsal
extension".
– During operation the display will
show the symbol
.
stretching in plantar flexion
With the special „stretching in plantar
flexion" function the carriage gently
stretches the joint by bending the foot
downward.
Starting at the middle position the car-
riage will first move to the programmed
dorsal extension value and then to the
programmed plantar flexion value.
Subsequently the carriage reverses
5° towards dorsal extension and then
moves very slowly back again to the
programmed plantar flexion value (dis-
play
) After that it attempts to attain
another 5°, moving even slower than
before (display
).
If a high resistance toward the ad-
ditional 5° is sensed, the reverse on
load function is automatically activated
and the carriage moves in the opposite
direction.
This stretch cycle is repeated ten times.
After that the carriage moves to the
programmed maximum dorsal exten-
sion value and restarts the plantar
flexion stretch cycle.
default setting: disabled
Note!
– If a pause is programmed when you
enable the function, the carriage will
stop for the duration of the pause
each time the maximum stretching
value is attained.
– Enabling the plantar flexion stretch
function automatically disables mo-
tor B. The only movement performed
is dorsal extension / plantar flexion.
– It is not possible to combine a second
stretching function with the special
function „stretching in plantar
flexion".
– During operation the display will
show the symbol
.
stretching in inversion
With the special „stretching in inversion"
function the carriage gently stretches
the joint towards the inside.
Starting at the middle position the
carriage will first move to the pro-
grammed eversion value and then to the
programmed inversion value.
Subsequently the carriage reverses 5°
towards eversion and then moves very
slowly back again to the programmed
inversion value (display
for the right
foot and
for the left foot). After that
it attempts to attain another 5°, moving
even slower than before (display
for
the right foot and
for the left foot).
If a high resistance toward the ad-
ditional 5° is sensed, the reverse on
load function is automatically activated
and the carriage moves in the opposite
direction.
This stretch cycle is repeated ten times.
After that the carriage moves to the
programmed maximum eversion value
and restarts the inversion stretch cycle.
default setting: disabled

Publicité

Chapitres

Table des Matières
loading

Table des Matières