1/2" (1.27 Cm) Overlay Panel Dimensions - Monogram ZKFN Instructions D'installation

Design Guide - Flush Inset Installation for

1/2" (1.27 cm) OVERLAY PANEL DIMENSIONS

For a more custom appearance, overlay panels may be installed on trimmed models. The
overlay panel must be secured to a 1/4" (0.63 cm) thick backer panel which slides into the
trim. A spacer panel 0.10" (0.25 cm) thick must be placed between the overlay and backer
panel.
Assemble the panels with glue and screws:
• Center the spacer panel on the backer panel, left to right and top to bottom. Secure the
panels with glue.
• Refer to the following chart for locating the backer panel to the overlay panel. Secure the
overlay panel to the backer panel with glue and screws. Screws must be countersunk into
the backer panel.
Hinge Side
C
Freezer
Back
Backer with
Overlay Panel
Assembly
D
A
B A
IMPORTANT NOTE – DISPENSER MODELS
This kit is supplied with 2 dispenser trims. The flush
installation trim is designed to fit a total panel thickness
of 0.85" (2.16 cm) or 0.75" (1.91 cm).
• If the panel is less than 0.75" (1.91 cm) a noticeable
gap may be created around the dispenser trim.
• If the panel is more than 0.85" (2.16 cm) the dispenser
trim cannot be secured to the door.
Panel Dimensions
13-5/16"
F
E
11"
IMPORTANT NOTE: Maximum total weight for the assembled panels:
• Fresh food door panel – 75 lbs.(34 kg) • Freezer door panel – 53 lbs.(24 kg) • Grille Panel – 18 lbs. (8.16 kg)
Side-by-Side Refrigerator
C
Fresh Food
Back
SxS Fresh Food
SxS Freezer
D
SxS Grille
B
36" Side-by-Side Fresh Food
1/4" Backer Panel 68-3/8" x 18-9/16" 68-3/8" x 14-9/16"
.10" Spacer Panel 67" x 17-9/16"
1/2" Overlay Panel 68-5/8" x 20-7/8"
42" Side-by-Side Fresh Food
1/4" Backer Panel 68-3/8"x 24-9/16"
.10" Spacer Panel 67" x 23-9/16"
1/2" Overlay Panel 68-5/8" x 26-7/8"
48" Side-by-Side Fresh Food
1/4" Backer Panel 68-3/8" x 26-9/16" 68-3/8" x 18-9/16"
.10" Spacer Panel 67" x 25-9/16"
1/2" Overlay Panel 68-5/8" x 28-7/8"
Grille Back
C
A B
D
A B
2-1/16" 1/4"
2-1/16" 1/4"
2-1/16" 2-1/16"
• The overlay panel must be constructed according to
the specifications shown to achieve the correct total
thickness.
• Cut the dispenser opening after the backer, spacer
and overlay panels have been assembled.
Freezer
33-7/8" x 9"
67" x 13-9/16" 33" x 8-3/8"
68-5/8" x 16-7/8" 38" x 11-3/16"
Freezer
68-3/8" x 14-9/16" 39-7/8" x 9-1/2"
67" x 13-9/16" 39" x 8-5/8"
68-5/8" x 16-7/8" 44" x 11-3/16"
Freezer
45-7/8" x 9-1/2"
67" x 17-9/16" 45" x 8-5/8"
68-5/8" x 20-7/8" 50" x 11-3/16"
62
Door
1/4"
Backer
Panel
.250" + .10" + .50" = .85"
0.63 + 0.25 + 1.27 = 2.16 cm
Total Panel Thickness
C D
1/8" 1/8"
1/8" 1/8"
1-15/32"* 7/32"
*2" for 36" models
Grille Dispenser Cutout Position
E
34-9/32"
Grille Dispenser Cutout Position
E
34-9/32"
Grille Dispenser Cutout Position
E
34-9/32"
1/2"
Overlay
Panel
.10"
Spacer
F
3-15/16"
F
3-15/16"
F
5-15/16"
31-1000454 Rev. 0