Current Time Setting Procedure; On - Timer Operation; Off - Timer Operation; Program Timer Operation - Mitsubishi Heavy Industries FDT Manuel De L'utilisateur

HOW TO USE < WIRELESS REMOTE CONTROL >
HOW TO OPERATE
• Turn on the power supply of both indoor/outdoor units for six hours before starting the unit to protect the units. (The
ATTENTION
crankcase is conducted and the compressor is heated) Do not turn off the power supply. (The crankcase heater is conducted
while the compressor is stopped, preventing failure of the compressor due to accumulation of liquid refrigerant by keeping the
compressor warm.)
• The operation of remote control must be performed slowly and steadily.
OPERATION
1
1
Press
5
The operation display light (Green) turns on, and the operation starts.
4
The setting status is displayed on the liquid crystal area on the remote
2
control.
3
2
Press MODE button.
Operation mode
Current operation mode is indicated with the
AUTO
operation mode icons.
COOL
The mode will change in the following order by pressing the button.
HEAT
DRY
3
FAN
Press TEMP button.
Set the room temperature by pressing
Guideline of room temperature setting
4
COOL ...............26 to 28°C
Press FAN SPEED button.
DRY ..................21 to 24°C
→ HI → MED → LO — FAN SPEED can be changed in order.
HEAT ................22 to 24°C
FAN ................... TEMP setting is
5
Press AIR FLOW button.
unnecessary
Effective AIR FLOW direction
• Operation mode can be changed even
AUTO mode operation ............ Intermediate
when the unit stops.
Cooling, dehumidifying mode ... Horizontal
• If you operate under the same condition
Heating mode ......................... Downwards
(operation mode, set temperature,
airflow, louver) just follow step 1, no
Stop
other operations are necessary. The
conditions which were set previously are
indicated on the remote control

CURRENT TIME SETTING PROCEDURE

The timer is set on the current time. Adjust the current time correctly at first of all.
[EXAMPLE] AM (morning) 8:00 setting
1
Press TIME SET UP switch.
Press it with the tip of ballpoint etc. The time display blinks and can be set
to the current time.
2
Press
2
Morning : AM After noon : PM
The displayed time changes by 1 minutes when pressing the button.
• If
1·3
NOTICE
• In case the buttons are not pressed for 60 seconds, the displayed time is set as
current time without step 3.
3
Press TIME SET UP switch.
The display changes from blinking to steady lighting and the setting is
completed.
12
button.
marks besides the
(AUTO) (COOL) (HEAT)
(FAN) (DRY)
or button.
☞
see page 13
Press button
or button to adjust to AM 8:00.
or button is pressed during the blinking, fast-forward or fast-
backward can be done.
ON – TIMER OPERATION
Operation is started at the setting time.
[EXAMPLE] If you would like to start the operation at AM 8:00
1
Press ON timer button.
ON timer display
2
Press
Displayed time will be changed by 10 minutes by pressing the buttons.
3
Press ON timer button.
• ON timer display
the setting is completed.
2
(Press within 60 seconds)
TIMER/CHECK display lamp of the air conditioner is lit. (The receiving part of
indoor unit)
1·3 • At AM 8:00, TIMER/CHECK display lamp turns off and the air conditioner
will start operating.
Cancellation
• Press CANCEL button to turn off the TIMER display and timer is canceled.
• After TIMER setting, if ON/OFF button is pressed before the setting time,
In case the ON timer is set while the air
TIMER display turns off and the TIMER is canceled.
conditioner is in operation, it will be stopped
Time change
and ready for restart at the setting time.
Press ON TIMER button to set again.
OFF – TIMER OPERATION
Operation is stopped at the setting time.
[EXAMPLE] If you would like to stop the operation at PM 9:00
1
Press ON/OFF button when the air conditioner stops.
The air conditioner starts to operate.
OFF timer can be set only in case the air conditioner is in operation.
2
Press OFF timer button.
1
OFF timer display
3
Press
Displayed time will be changed by 10 minutes by pressing the buttons.
3
4
Press OFF timer button.
• OFF timer display
2· 4
the setting is completed. (Press within 60 seconds)
TIMER/CHECK display lamp of the air conditioner is lit. (The receiving part
of indoor unit)
• At PM 9:00, TIMER/CHECK display lamp turns off and the air
Cancellation will stops operating.
• Press CANCEL button to turn off the TIMER display and timer is canceled.
• After TIMER setting, if ON/OFF button is pressed before the setting time, TIMER display turns off and the TIMER is canceled.
Time change
Press OFF TIMER button to set again.

PROGRAM TIMER OPERATION

By setting both ON timer and OFF timer, the settings turn into PROGRAM timer mode. Operation and stopping can be performed at the
same time of each day by setting program timer once.
1
Set ON timer.
Press ON timer button and set the time with
Press ON timer button again.
2
Set OFF timer.
Press OFF timer button and set the time with
Press OFF timer button again.
Both ON TIMER and OFF TIMER are displayed. The direction of arrow mark
1 2
changes depending on the status of operation.
Cancellation
• Whenever the CANCEL button is pressed, both ON and
OFF timer display will be turned off and the PROGRAM
timer mode will be cancelled. (Operation condition is kept as
before the button is pressed.)
• Whenever the ON/OFF button is pressed, both ON and OFF
timer display will be turned off and the PROGRAM timer
mode will be cancelled. The air conditioner stops operating.
< WIRELESS REMOTE CONTROL >
blinks.
or button to adjust to AM 8:00.
changes from blinking to steady lighting and
blinks.
or button to adjust to PM 9:00.
changes from blinking to steady lighting and
conditioner
or button.
or button.
(stop) (operating)
Changing the set time
Press OFF TIMER button or ON timer button to set again.
NOTICE
The same time cannot be set for OFF timer and ON timer.