Programming Automatic Closing; Activating Automatic Closing (Max Timer 120S); Deactivating Automatic Closing; Setting Inputs 18 And - SOMFY Elixo 800 Manuel D'installation

9.2. Programming automatic closing

To programme automatic closing, use the PAUSA and PROG
buttons of the control unit.
9.2.1. activating automatic closing
(max timer 120s)
[1]. With the control unit powered and the gate closed (FCC LED
off), press the PROG button.
The DL 10 LED will flash to indicate that the control unit is in
programming mode.
[2]. Press and hold the PAUSA button until the contacts «click».
The indicator will come on.
The control unit will start counting the seconds (indicated by
the intermittent flashing of the indicator) for the automatic
gate closure delay.
[3]. Press the PAUSA button when the required time is reached.
The control logic will memorise the time elapsed between the
two presses of the PAUSA button.
The automatic closure delay of the gate is programmed.
Note: if the PAUSA button is not pressed a second time, the
control unit will automatically exit the programming mode after
120 seconds and store the maximum time of 120 seconds for the
automatic closing delay.

9.2.2. deactivating automatic closing

[1]. With the control unit powered and the gate closed (FCC LED
off), press the PROG button.
The DL 10 LED will flash to indicate that the control unit is in
programming mode.
[2]. Press and hold the PAUSA button until the DL10 LED goes out.
The control unit will exit the programming phase, automatic
closing is deactivated.

9.3. setting inputs 18 and 19

To set the parameters for inputs 18 and 19, use the PAUSA,
LAVORO and PROG buttons of the control unit.

9.3.1. setting input 18

to have input 18 in oPEN only:
[1]. Disconnect the control unit.
[2]. Press the PROG, LAVORO and PAUSA buttons at the same time and then reconnect the control logic while keeping the
buttons pressed.
to switch input 18 back to PEdEstriaN oPEN/ClosE:
[1]. Disconnect the control unit.
[2]. Press the LAVORO and PAUSA buttons at the same time and then reconnect the control logic while keeping the buttons pressed.
9.3.2. setting input 19
to have input 19 in ClosE only:
[1]. Disconnect the control unit.
[2]. Press the PROG and PAUSA buttons at the same time and then reconnect the control logic while keeping the buttons
pressed.
to switch input 19 back to oPEN/ClosE:
[1]. Disconnect the control unit.
[2]. Press the PROG and LAVORO buttons at the same time and then reconnect the control logic while keeping the buttons pressed.
Copyright © 2011 Somfy SAS. All rights reserved.
PAUSA LAVOR LAVOR A A O O PROG
20 20
19 19
START START
18 18
PED PED
STOP STOP
FOTO FOTO
FCA FCA
PAUSA LAVORO PROG
PAUSA LAVORO PROG
DL10 DL10
FCC FCC
[1]
COSTA COSTA
10 10
9 9
DL10
DL10
PAUSA LAVORO PROG
PAUSA LAVORO PROG
DL10
8 8
[2] 7 7
6 6
5 5
DL10
4 4
3 3
F1 F1
2 2
PAUSA LAVORO PROG
[3]
1 1
DL10
PAUSA LAVORO PROG
PAUSA LAVORO PROG
[1]
DL10
DL10
PAUSA LAVORO PROG
PAUSA LAVORO PROG
[2]
DL10 DL10
PAUSA LAVOR O PROG
20 20
19 19
START START
18 18
PED PED
STOP STOP
FOTO FOTO
FCA FCA
DL10 DL10
FCC FCC
COSTA COSTA
10 10
9 9
8 8
7 7
6 6
5 5
4 4
3 3
F1 F1
2 2
1 1
Elixo 800/1300/2000
DL12 DL12
PROG PROG
F2 F2
DL11 DL11
...
DL12 DL12
PROG PROG
F2 F2
DL11 DL11
15