EDELRIDe MEGAWATT Mode D'emploi page 25

• if there are doubts concerning safe use;
• if sharp edges have the potential to damage the rope or
hurt the user;
• if visible signs of damage material (e.g. cracks, plastic
deformation);
• if the material shows deep corrosion or had contact
with chemical substances;
• if lever does not close by itself and fully.
• if the product has been subjected to a hard fall load or
high shock loads occurring in a pendulum fall.
INSPECTION AND DOCUMENTATION
In case of commercial use, the product must be inspect-
ed regularly or at least once a year by the manufacturer,
a qualified person or an approved inspection body/
agency; thereafter it may have to be serviced or removed
from use. Legibility of the markings has to be checked.
Such inspections and service must be documented for
each product. The following information must be record-
ed: Product identification and name, manufacturer's
name and contact details, unique identification, date of
manufacture, date of purchase, date of initial use, date of
next regular inspection, result of inspection, and signa-
ture of qualified person responsible. A suitable speci-
men is found at www.edelrid.de
In case of commercial use, the relevant information con-
tained in this user manual must be made available to
each user before using the product.
STORAGE, MAINTENANCE AND TRANSPORT
STORAGE
Store cool, dry, and protected from daylight outside
transport containers. Prevent contact with chemicals
and store without mechanical stress.
MAINTENANCE
Clean contaminated products in hand warm water and
rinse properly. Dry at room temperature, never in dryers
or near heaters/ radiators! Commercial disinfectants
based on alcohol (isopropanol) may be used if
necessary.
TRANSPORT
The product must be kept away from chemicals, dirt and
mechanical damage. For this purpose, a protective bag or
special storage and transport containers should be used.
PRODUCT MARKING
Manufacturer: EDELRID
Model: MegaWatt
Product designation: Rope adjustment device, descend-
er device for rescue, braking device and descent device
in accordance with EN 12841:2006/C, EN 341:2011/
2A, EN 15151-1:2012/8 and ANSI/ASSE Z359.4:2013
Lot number
2777: The identification of the notified body monitor-
ing the production of the PPE (SATRA Technology Europe
Ltd, Bracetown Business Park, Clonee, Dublin 15, Dublin,
Ireland)
The warning message and instructions must be read
and observed
YYYY MM: Year and month of manufacture
Instruction for the correct feeding of the rope
Standard EN 12841-C:
• only use with Kernmantelrope according to EN 1891
• Max. load: max. 150 kg
• Diameter range: 10 mm ≤ Ø ≤ 11,8 mm
• Max. load: rescue: 200 kg
• Diameter range for rescue: 10 mm ≤ Ø ≤ 11,5 m
Standard EN 341:
• "2A": manually-operated descender device (type 2)
with descent energy class A of up to 7,5 x 10
• 200 m: tested for descending of up to 200 consecu-
tive meters
• T > -30°C: usage only for temperatures above – 30°C
• Performance Static 11,0 mm: Only use with this rope
according to EN 341
• Range of load incl. equipment: 30 – 120 kg
Standard EN 15151-1/8:
• Rope diameter range: 8,9 mm ≤ Ø ≤ 11,0 mm
Standard ANSI/ASSE Z359.4:
• EN 1891; 10 mm ≤ Ø ≤ 11,5 mm: only use with
Kernmantelrope according to EN 1891-A and shown
rope diameter range,
• 200 m: tested for descending of up to 200 consecu-
tive meters
• Max. load: 59 - 141 kg
• Multiple use: May be used for several descents
DECLARATION OF CONFORMITY
EDELRID GmbH & Co. KG herewith declares that this
article is in conformity with the essential requirements
6
J