Nice AVIO500 Instructions Et Avertissements Pour L'installation Et L'utilisation page 42

STEP 5
START
RADIO
If, at the start of the following procedures, the "set",
"radio" and "error" LEDs flash, it means that the program-
ming protections have been activated – see Paragraph
10.3.1.
Therefore, radio transmitters learning is not possible.
To interrupt the following programming procedures at
any time, press the RADIO button or wait 20 seconds.
5.1 – TESTING THE RADIO TRANSMITTER
To test the transmitter just press one of its 4 keys, make sure that
the red LED [A] flashes and that the automation carries out the
related command.
The command associated to each button depends on how it has
been memorised.
32
T1
T3
5.2 – START BUTTON PROGRAMMING
This procedure allows for programming the button of the radio
control linked to the automation's start function.
ACTION
PRESS THE RADIO
01.
BUTTON FOR 1
SECOND
PRESS THE DESIRED
BUTTON ON EVERY
02.
TRANSMITTER TO BE
PROGRAMMED
PRESS THE RADIO
BUTTON UNTIL RADIO
03. LED TURNS OFF OR
WAIT 20 SECONDS TO
EXIT THE PROCEDURE
16 – English
TRANSMITTER PROGRAMMING
SET
[A] Led
T5
T2
T4
[B]
RESULT
The red "radio"
LED turns on in the
fixed mode (if not,
consult Paragraph
10.3.1)
The red "radio"
LED flashes
The red "radio"
LED turns off
5.3 – PROGRAMMING OF THE BUTTON LINKED TO THE
"OUT1" OUTPUT
This procedure allows the programming of the remote control but-
ton connected to the "OUT1" output (1-2 terminals).
ACTION
PRESS THE
01. DIO BUTTON FOR 1
SECOND
PRESS THE
02. BUTTON FOR 1
SECOND
PRESS THE DESIRED
BUTTON OF ALL THE
03.
TRANSMITTERS TO BE
PROGRAMMED
PRESS THE RADIO
BUTTON UNTIL RADIO
04.
LED TURNS OFF OR
WAIT 20 SECONDS TO
EXIT THE PROCEDURE
5.4 – PROGRAMMING OF THE BUTTON LINKED TO THE
ON-BOARD COURTESY LIGHT
This procedure allows for programming the button of the radio
control linked to the on-board led courtesy light.
ACTION
PRESS THE
01. DIO BUTTON FOR 1
SECOND
PRESS THE
02. BUTTON FOR 1
SECOND
PRESS THE DESIRED
BUTTON OF ALL THE
03.
TRANSMITTERS TO BE
PROGRAMMED
PRESS THE RADIO
BUTTON UNTIL RADIO
04. LED TURNS OFF OR
WAIT 20 SECONDS TO
EXIT THE PROCEDURE
5.5 – DELETING ALL MEMORISED TRANSMITTER
This operation deletes all memorized transmitters from the
memory.
ACTION
PRESS THE RADIO
BUTTON FOR 4
01. SECONDS AND
RELEASE WHEN
RADIO LED FLASHES
PRESS THE RADIO
02. BUTTON AGAIN
FOR 1 SECOND
MEMORY DELETION
03.
COMPLETED
5.6 – DELETING A SINGLE TRANSMITTER
This operation deletes a single transmitter from the memory.
RESULT
RA-
The red "radio" LED
turns on in the fixed
mode
The red "radio" LED
START
remains lit in fixed
mode and the red
"error" LED turns
on in fixed mode
The red "radio" LED
flashes and the red
"error" LED ramins
lit in fixed mode
The red "radio" LED
and the red "error"
LED turn off
RESULT
RA- The red "radio" LED
turns on in the fixed
mode
The red "radio"
LED remains lit in
SET
fixed mode and the
yellow "set" LED
turns on in fixed
mode
The red "radio"
LED flashes and the
yellow "set" LED
ramins lit in fixed
mode
The red "radio" LED
and the yellow "set"
LED turn off
RESULT
The red "radio" LED
flashes
The red "radio" LED
flashes fast
The red "radio" LED
turns off