Publicité
Les langues disponibles
Les langues disponibles
Fitting out the removable hatch, Figs. 173 - 175, Plan II
Part
Description
No.
378
Boiler pipe
379
Boiler end panel
380
Boiler end panel
381
Instrument panel
382
Instrument panel support
383
Boiler support
384
Boat support
385
Inflatable boat
386
Transport bar
- Fit the boiler end panels 379 and 380 on the boiler pipe.
Glue the instrument panel 381, 382 to the boiler. Place the
boiler on the boiler supports 383, and glue this assembly
on the hatch.
- Glue the supports 384 for the inflatable boats 385 on the
hatch and the boat deck 320. Glue the front inflatable
boat in place.
Deck and superstructure fittings, Figs. 176 - 181, plans I and II
Part
Description
No.
387
Outrigger support
388
Brace
389
Lamp plinth
390
Lamp mast
391
Companionway
392
Ladder
393
Spacer pin
394
Deck lamp
395
Deck lamp stand
396
Light shaft
397
Latch
398
Glazed porthole
399
Pulley console
400
Return pulley
401
Washer
402
Lamp console
403
Liferaft
404
Catapult arm
405
Catapult foot
406
Catapult strut
407
Lifebelt
408
Gangway brace
408a
Gangway grid
Outrigger support and stern light
- Assemble the outrigger support from parts 387 and 388,
and glue it in the 3 mm Ø hole in the removable hatch.
- Remove the cylindrical spigot from the lamp plinth 389.
Sand the rear corners as shown, and glue the plinth to the
tube 390.
- Glue the tube in the 3 mm Ø hole, ending flush on the
underside. The method of fitting the stern lamp is descri-
bed in the section entitled "Lighting".
Assembly instructions
Happy Hunter
Material
Aluminium
Aluminium
Aluminium
ABS
ABS
ABS
ABS
Plastic
Brass
- Drill two 1 mm Ø holes at the balance point of the rear
inflatable boat to accept the transport bar 386 as shown
in the detail view. Bend the bar to shape and insert it in
the holes.
- The purpose of the bar is to enable the crane to raise the
inflatable boat and lower it to the water. Place the inflata-
ble boat on the boat supports.
Material
Brass
Brass
ABS
ABS
Plastic
Brass
Brass
Aluminium
Brass
ABS
Brass
Brass
ABS
Aluminium
Brass
ABS
Plastic
Brass
Brass
Brass
Plastic
ABS
Brass
Companionways, ladders and deck lamps
- Cut the six companionways 391 to length as shown on
the plan, bevel their front faces and glue them in place.
The companionways on the removable hatch should be
glued to the edge of the hatch only; don't glue them to the
deck.
- Cut five ladders 392 to length for fitting to the superstruc-
ture, the wheelhouse and the aft bulkhead. Bend them as
required, drill 1 mm Ø holes for them and insert them in
the holes. The ladders should not be glued in place until
the railings have been completed.
44
Size in mm
No.
off
22 Ø x 20 Ø x59
1
Machined
1
Machined
1
1, die-cut
1
1, die-cut
2
3, machined
2
1.5, die-cut
4
Inj. moulded
2
1 Ø x 80
1
Size in mm
No.
off
0.2 x 3 x 17
1
2.2 Ø x 3 Ø x 42
1
Inj. moulded
1
3 x 3 x 45
1
Overlength
6
Overlength
7
1 Ø
8
Machined
2
1 Ø
2
Inj. moulded
1
1 Ø
2
6 Ø x 8 Ø
1
Inj. moulded
4
Machined
4
2.2 I.D.
4
Inj. moulded
1
Inj. moulded
2
1.5 Ø
4
1.5 Ø
4
1.5 Ø
2
20 Ø
8
Ready made
8
1 Ø x 90
7
Order No.
1106
Notes
FS
Notes
As plan
As plan
As plan
FS
As plan
As plan
FS
As plan
As plan
As plan
FS, inj. moulded
Publicité
