Publicité
Les langues disponibles
Les langues disponibles
Fitting out the after deck and the forecastle deck, Figs. 145 - 152, Plan 1
Part
Description
No.
279
Hawse barrier
280
Two-part hawse
281
Hawser pulley
282
Hawser block
283
Small return roller
284
Double cruciform bollard
285
Towing complex
286
3" Smith brake
287
Brake shoe
288
Stub
289
Elbow fitting
290
Front connection
291
Oil valve
292
Rear oil connection
293
Mechanical valve
294
5" valve
295
Gooseneck
296
Guard cradle
297
Vertical guard
298
Capstan gearbox
299
Capstan drum
300
Axle
301
Fire extinguisher box
302
Shield
303
Return pulley
304
Pulley pin
- Drill the holes for the hawse barrier 279 in the hatch 63.
Glue the two-part hawses 280 in the barrier, and position
this assembly on the boat (see Fig. 182 for the compo-
nents).
- Drill the holes in the roller box 78 - 81 and glue the haw-
ser pulleys 281 and the hawser blocks 282 in place.
- Glue the return pulleys 283 to the bulwark. Remove the
base plates of the double cruciform bollards 284, which
are glued to the main deck bulwark. Glue all the bollards
284 in place in the positions shown.
- Glue parts 285 and 286 in place.
- Drill the appropriate holes in the after deck. Position parts
287 - 295 as shown in the plan view and the detail views.
The funnels, Figs. 153 - 159
Part
Description
No.
305
Internal funnel wall
306
Lower centre floor
307
Floor
308
Funnel shell
309
Funnel fairing
310
Large exhaust pipe
311
Small exhaust pipe
312
Large air shaft
313
Small air shaft
314
Funnel door
315
Draught flap
316
Aerial holder
317
Door latch
318
Handrail
319
Split pin
Assembly instructions
Happy Hunter
Material
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
Aluminium
Aluminium
Brass
Spruce
PVC
Aluminium
Brass
The capstans
- The capstans are assembled from parts 296 - 300; note
that the end of the axles 300 must be splayed slightly
before fitting. Glue the capstans 298 - 300, the guard
cradles and the vertical guards 296, 297 on the deck.
Parts 301 - 304
- Apply the decal "F" to the fire extinguisher box, and glue
it to the after bulkhead.
- Cut the towing winch compartment shields 302 to a
length of 23 mm. Cut slots in the after bulkhead as shown
in the detail view, and glue the shields over the openings.
- Install the return pulleys 303 on the forecastle deck using
the pins 304. Splay one end of the pins and cut them to
length after fitting them. Apply a fillet of Stabilit-Express
round the projecting ends.
Material
ABS
ABS
ABS
ABS
ABS
Brass
Brass
ABS
ABS
ABS
ABS
Brass
Brass
Brass
Brass
41
Size in mm
No.
off
Inj. moulded
1
Inj. moulded
2
Inj. moulded
2
Inj. moulded
2
Inj. moulded
2
Inj. moulded
11
Inj. moulded
1
Inj. moulded
2
Inj. moulded
2
Inj. moulded
2
Inj. moulded
2
Inj. moulded
4
Inj. moulded
4
Inj. moulded
4
Inj. moulded
1
Inj. moulded
2
Inj. moulded
6
Inj. moulded
2
Inj. moulded
2
Machined
2
Machined
2
2 Ø x 22
2
5 x 10 x 13
1
0.4 x 38 x 23
2
6 Ø x 2
4
2 Ø x 4.5
4
Size in mm
No.
off
1.5, die-cut
2
1.5, die-cut
4
1.5, die-cut
2
1.5
1 each L / R, vac.
1.5, die-cut
2
9 Ø x 7.5 Ø x 7
4
4 Ø x 3.2 Ø x6.5
4
1, die-cut
4
1, die-cut
1
1, die-cut
2
1, die-cut
4
1 Ø x 19
1
1 Ø
8
1 Ø
6
1 Ø x 15
1
Order No.
1106
Notes
FS
FS
FS
FS
FS
FS
FS
FS
FS
FS
FS
FS
FS
FS
FS
FS
FS
Oversize
FS
Machined
Notes
As plan
As plan
Publicité
