Publicité
Les langues disponibles
Les langues disponibles
51
Battery support base plate
52
Reinforcing strip
53
Drive battery
54
Cable, red
55
Spade connector with insulator
55a
Spade connector with insulator
56
Cable, black
1B - 3B
Bow thruster
- Fit the washers 32 and the bushes 33 on the rudders 31,
slide them into place and engage them in the bottom bus-
hes 29 - Fig. 25.
- Fit an O-ring 34, a second washer 32 and a tiller assem-
bly 35 - 37 on the top end of each rudder shaft - Figs. 26
and 27.
- Check the alignment of the entire power system and rud-
der system inside the hull: the shafts and propellers must
rotate freely and smoothly. Ensure that the rudders are
exactly parallel when viewed from the side and from
underneath. The propeller shaft tubes must not be under
stress. If necessary file out the 7 mm holes in the shaft fai-
rings until this is the case. It may be necessary to file back
the central Kort nozzle strut slightly - see arrow in Fig. 23.
- Glue the speed controller support assembly against the
keel in-fill piece, and glue the motor bulkhead to the
speed controller support. Glue the Kort nozzles in the hull,
and the stern tubes in the shaft fairings.
- Check that the rudders rotate smoothly, but without any
tendency to slip out of the bottom bushes 29. Glue the
rudder bushes in place.
- Sand back the keel in-fill piece to the point where it ends
at the same height as the Kort nozzles inside the hull.
Snip off the front arm of the right-hand tiller - Fig. 27.
- Glue the servo support plate 38 to the keel in-fill piece
and the Kort nozzles, in the position shown on the plan.
- Fit the rudder servo 39 in the servo mount 40, and place
the mount on the servo support plate, but do not secure
it at this stage. Set the servo to centre and move both
rudders to the "straight ahead" position. Align the tillers
carefully, press them down lightly and tighten the socket-
head screws 37.
- Connect the system using the pushrods 41 - 44. Align the
servo, and attach the servo mount to the servo support -
Figs. 28, 29.
The after deck
Part
Description
No.
57, 58
Frame
59
After deck
60
Deck girder
61
Deck girder
62, 63
Hatch cover
64
Swivel latch
65
Countersunk screw
66 - 69
Frame side panel
70
After deck support girders
71
Reinforcing rail
72
After bulkhead
73
Support rail
Assembly instructions
Happy Hunter
ABS
ABS
---
---
---
---
---
---
- Fit the connectors 46 to the motor side of the speed con-
troller 45. Fix the speed controller(s) and the auxiliary
system battery 47 to the speed controller support using
strips of Velcro (hook-and-loop) tape 48 - Fig. 31.
- Assemble the battery holder from the formers 49 and 50,
the base plate 51 and the square strips 52, which have to
be cut to length - Figs. 32, 33. Note: if you are using bat-
teries other than the ones we recommend, you will need
to modify the battery opening to suit.
- Trim the battery holder to fit in the hull in the position
shown in the side elevation, and glue it in place.
- Fit the batteries 53, and connect them to the speed con-
troller(s) using the cables 54, 55 and 56. If you are using
two controllers, fit another connector in the battery
connecting harness. Read the speed controller instruc-
tions, and take care to observe correct polarity.
- Make up the connecting lead 55, 56, and connect it - Fig.
34.
- The spade connectors 55a are required if you wish to
install auxiliary working systems.
Bow thruster
- Assemble the bow thruster 1 B as described in the
instructions supplied with the set.
- Suppress the motor using the suppressor set 168, and
solder the cables 2 B to the motor.
- Tape the bow thruster tubes 3 B together, and trim the
holes in the hull to obtain as snug a fit as possible. Take
care to set the bow thruster horizontal - Figs. 35 - 37.
- Assemble the bow thruster inside the hull, align it careful-
ly and mark the excess length of the outer tubes.
- Shorten the tubes at the marked points and glue them to
part 1 B. Glue the bow thruster in the hull, taking great
care to make the joints watertight. Sand back the excess
tube length flush with the hull - Figs. 38 - 41.
Material
ABS
ABS
ABS
ABS
ABS
Plastic
Steel
ABS
ABS
ABS
ABS
ABS
30
1.5, die-cut
1
3 x 3
3
-
2
1.5 mmÇ
1
4.8 x 0.8
4
6.3 x 0.8
5
1.5 mmÇ
2
Set
1
Size in mm
No.
off
1.5, die-cut
1 each
1.5, die-cut
1
1.5, die-cut
2
1.5, die-cut
1
1.5, die-cut
1 each
Inj. moulded
12
2.2 Ø x 6.5
12
1.5, die-cut
2 each
2 x 2, as plan
2
3 x 3, as plan
1
1.5, die-cut
1
2 x 2, as plan
1
Order No.
1106
As plan
Not included
PS, overlength
PS
PS, overlength
Not included
Notes
Publicité
