ROBBE Happy Hunter Notice De Montage Et De Mise En Œuvre page 31

74 Door
75, 76 Companionway wall
77 Reinforcing rail
78 Front roller box wall
79 Roller box doubler
80 Roller box cover
81 Roller box side panel
Note: while you are working on the after deck please take
care not to assemble it the wrong way round.
- Mark the position of the frames 57 and 58 on the under-
side of the after deck 59, and glue them in place.
- Glue the deck girders 60, 61 in place leaving 3 mm spa-
cing to the edges of the deck - Fig. 43.
- Trim the hatch covers 62, 63 and fit them. Fit the swivel
latches 64, 65 - Fig. 44.
- Glue the frames 66, 67 and 68, 69 to the underside of the
hatch covers - Fig. 45.
- Attach the deck support girders 70 just below the upper
marked line in the hull. The butt joint should be located in
the centre of the transom - Fig. 46.
- Clamp the support girders to the hull, ensure there are no
gaps, and glue them in place by running drops of cyano
along the joints.
- Cover the installed RC and power system components to
protect them. Trial-fit the after deck, trim it as required,
and glue it in place. Sand the hull down flush with the
after deck in the stern area - Fig. 47.
Stern bulwark
Part Description
No.
82 Stern bulwark
83 Bulwark section
84 Handrail
85 - 89 Aft bulwark stanchion
90 Aft bulwark stanchion
91 Aft bulwark stanchion
92 Large starboard oil cradle
93 Large port oil cradle
94 Small starboard oil cradle
95 Small port oil cradle
96 Roller
97 Roller fairing
98 Main deck
99 Deck superstructure coaming
100 Removable hatch coaming
101 Foreship bulkhead
102 Reinforcing rail
103 Deck girder
- Position the stern bulwark 82 flush with the opening of the
roller box, align it carefully and tack it to the roller box in
the centre with a little cyano.
- Curve the bulwark towards the hull on both sides, and
tack it in place until just short of the ends.
- Mark the cut line on part 82, cut the bulwark to size, but
do not glue it finally - Fig. 57.
- Cut the scuppers and hawses from the bulwark sections
83. Glue parts 83 butting up against the after bulkhead, at
Assembly instructions
Happy Hunter
ABS
ABS
ABS
ABS
ABS
ABS
ABS
After bulkhead and roller box
- Cut the reinforcing rail 71 to a length of 211 mm, and glue
it in place - Fig. 49.
- Glue the support rail 73 to the inside of the after bulkhead
72, and stick the door 74 on the outside - Figs. 50, 51.
- Trim the after bulkhead to fit, and glue it in place - Fig. 52.
- Glue the companionway walls 75 and 76 in place together
with the trimmed reinforcing rails 77 - Fig. 53. It is a good
idea to paint the interior of the companionway grey at this
point, as it will be inaccessible later.
- Assemble parts 78 - 81 to form the roller box - Figs. 54,
55.
- Glue the completed roller box centrally to the after deck,
allowing for the thickness of the stern bulwark 82, which
will be fitted later - Fig. 56.
Material
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
Beech
Obechi
ABS
ABS
ABS
ABS
ABS
ABS
the same time applying a thin coating of Stabilit-Express
- Fig. 58.
- The trimmed stern bulwark can now be glued in place
permanently.
- Carry out any final trimming of the scuppers and hawses,
referring to the plan in the stern area - Fig. 60.
- Trim the handrails 84 to fit, tack them in place, then run
drops of cyano along the joints to fix them permanently -
Figs. 60, 61.
31
1, die-cut 1
1.5, die-cut 1 each
3 x 3, as plan 5
1.5, die-cut 1
1.5, die-cut 1
1.5, die-cut 1
1.5, die-cut 2
Size in mm No.
off
1, die-cut 1
1, die-cut 2
2 x 2 2
1, die-cut 2 each
1, die-cut 18
1, die-cut 2
Inj. moulded 1
Inj. moulded 1
Inj. moulded 1
Inj. moulded 1
8 Ø x 47 1
3 x 8 x 35 2
1.5, die-cut 1
1 1
1 1
1.5, die-cut 1
3 x 3 2
2 x 2 2
Order No.
1106
Notes
FS
FS
FS
FS
Vac. moulded
Vac. moulded
As plan
As plan