Publicité
Les langues disponibles
Les langues disponibles
154
Grubscrew
155
Axle
156
Base plate
157
Motor flange
158
End-support
159
Side panel
160
Gusset
161
Motor, geared 500 : 1
162
Coupling sleeve
163
Self-tapping screw
Refer to the detail drawing on Plan I and photos 100 to 102.
- Glue the discs 151 centrally to the drum hub 152.
- Fit the axle 155 so that the collets 153, 154 can be posi-
tioned accurately; glue the collets to the discs only.
- Glue the base plate 156 to the motor support, install the
motor 161 and fit the end-supports 158 on the anchor
Radar drive unit
Part
Description
No.
164
Motor support
165
Motor, geared 1000 : 1
166
Spacer block
167
Self-tapping screw
168
Suppressor set
Refer to the detail drawing on Plan 2 and photos 103 and
104.
- Screw the motor 165 to the motor support 164. Fix the
spacer blocks 166 to the motor support using the self-
RC installation and wiring
Part
Description
No.
169
Receiver
170
Receiver battery cradle
171
Receiver battery
172
Y-lead
173
Relay
174
Wire
175
Spade connector
175a
Distributor
176
Charge lead
177
Relay
178
Extension lead
179
Bow thruster speed controller
180
Spade connector
181
Sound module
182
Bass loudspeaker
182a
Bass loudspeaker housing
182b
Self-tapping screw
183
Multi-Switch decoder 16
184
Decoder servo lead
185
Transistor reversing module
186
Servo lead with plug
187
Servo lead with socket
188
Self-tapping screw
189
Servo lead
Assembly instructions
Happy Hunter
Steel
Brass
ABS
ABS
ABS
ABS
ABS
---
Plastic
Steel
drum unit. Couple the parts using the sleeve 162 and glue
the end-supports to the base plate. Attach the side
panels 159 and the gussets 160.
- Drill a 1 mm Ø hole in the drum.
- Screw the completed anchor winch to the mounting plate
150 using the self-tapping screws 163.
Material
ABS
---
Obechi
Steel
---
tapping screws 167.
All the completed drive systems are installed in the hull
once the RC system has been fitted and the auxiliary wor-
king systems have been wired up.
Material
---
ABS
---
---
---
Brass
---
---
---
---
---
---
---
---
---
ABS
Steel
---
---
---
---
---
Steel
---
35
M3 x 3
2
2 Ø x 55
1
1.5, die-cut
1
1.5, die-cut
1
1.5, die-cut
2
1.5, die-cut
2
1.5, die-cut
2
---
1
1 I.D. x 20
1
2.9 Ø x 9.5
2
Size in mm
No.
off
1.5, die-cut
1
---
1
5 x 15 x 20
2
2.2 Ø x 6.5
2
---
6
Size in mm
No.
off
---
1
1.5
1
---
1
---
3
---
1
1.5 Ø
2
6.3
2
---
3
AMP
1
---
1
---
1
---
1
---
2
---
1
---
1
1.5
1
2.9 Ø x 6.5
4
---
1
---
2
---
4
---
1
---
1
2.2 Ø x 6.5
6
---
1 - 3 Not included
Order No.
1106
Not included
Notes
Not included
Not included
Notes
Not included
Vac. moulded
Not included
Not included
Not included
PS
PS
PS
Not included
Not included
Not included
Not included
Not included
Vac. moulded
Not included
Not included
Not included
Not included
Not included
Publicité
