Télécharger Imprimer la page

ROBBE Happy Hunter Notice De Montage Et De Mise En Œuvre page 42

Publicité

Les langues disponibles

Les langues disponibles

Please note that you must make one right-hand and one
left-hand funnel.
- Glue the floors 306 and 307 to the funnel walls 305. Note
the markings for the exhaust pipes on the upper floors.
- Glue these units in the funnel shells 308. Trim the funnels,
and sand the inside faces flat.
- Glue the funnel fairings 309 in place, angled as shown.
- Make the exhaust pipes from the brass rings 310 and 311
and glue them together.
- Glue the doors 314 to the funnels.
The superstructure, Figs. 160 - 166, Plan II
Part
Description
No.
320
Boat deck
321
Front panel
322
Front side wall
323
Transverse wall
324
Partition wall
325
Side wall
326 - 328
Aft wall
329
Brace
330
End wall
331
Companionway brace
332
Companionway support
333
Air shaft wall
334
Door
335
Angled wall
336
Bridge deck
"V"
Template
337
Bridge deck bulwark
338
Navigation lamp bracket base
339
Lamp bracket side panel
340
Lamp bracket back panel
341
Lamp bracket top panel
342
Handrail
343
Bulwark stanchion
344
Reinforcing strip
- Glue the walls 321 - 324 to the underside of the boat deck
320.
- Glue the partition wall 324 in place, noting the 1.5 mm
spacing on both sides.
- Glue parts 325 - 335 in place as shown.
- If you are fitting auxiliary working systems, cut the oval
opening in part 336.
- Place the bridge deck 336 on the superstructure and align
it in such a way that it projects by the same amount on
both sides. Mark the centre. The bridge deck must not
rest on the wall 335; it should butt up against its rear
edge. The bridge deck bulwark 337 will be glued on part
335 at a later stage.
Assembly instructions
Happy Hunter
- Bevel the front face of the draught flaps 315 at the top.
These parts should be painted before they are glued in
place.
- Glue the aerial holder 316 to the left-hand funnel.
- Drill 1 mm Ø holes for the door latches 317 and the hand-
rails 318. Bend these parts to shape and insert them. Fit
the split pin 319 on the handrail for the right-hand funnel.
- Apply the self-adhesive decals "a", "b", "p" and "r".
- The completed funnels should not be glued in place until
the superstructure has been completed.
Material
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
- Glue the bridge deck in place using Stabilit-Express.
- Set the bulwark 337 central and glue it in place using the
template "V".
- Make up one right-hand and one left-hand navigation
lamp bracket from parts 338 - 341.
- Glue the lamp brackets in place.
- Trim the handrail 342 and the bulwark stanchions 343 to
fit and glue them in place. Cut the eleven reinforcing strips
344 to length and glue them to the inside of the super-
structure, referring to the detail view on Plan II.
42
Size in mm
No.
off
1.5, die-cut
1
1.5, die-cut
1
1.5, die-cut
2
1.5, die-cut
1
1.5, die-cut
1
1.5, die-cut
2
1.5, die-cut
1 each
1.5, die-cut
1
1.5, die-cut
1
1.5, die-cut
1
1.5, die-cut
1
1.5, die-cut
2
1, die-cut
2
1.5, die-cut
1
1.5, die-cut
1
1.5, die-cut
1
1.5, die-cut
1
1.5, die-cut
2
1.5, die-cut
2
1.5, die-cut
2
1.5, die-cut
2
2 x 2 x 290
1
1, die-cut
5
3 x 3
11
Order No.
1106
Notes
As plan

Publicité

loading

Ce manuel est également adapté pour:

1106