ROBBE Happy Hunter Notice De Montage Et De Mise En Œuvre page 40

- Bend the hawser deflector bars 248 and 249 to shape
from the oval brass tube supplied, as shown in the detail
view. Trim the deflector bar 249 to fit on the model; the
top edges should end flush with the handrails.
- Cut the hawser bar supports 250 and 251 as shown on
the plan, and solder them to the bars (away from the
model).
Figs. 140 - 144 show the sprues containing the injection-moulded parts required for the following stages.
Hatches and toolbox, Figs. 145 - 147, Plan I
Part Description
No.
253 Hatch frame
254 Tension frame
255 Spacer plate
256 Cover
257 Hatch cover
258 Handwheel
259 Hatch and cover
261 Handwheel
262 Hatch box
263 Hatch floor
264 Hatch cover
265 Handwheel
266 Box
267 Cover
268 Hatch block
269 Sliding hatch
270 Handle
271 Latch bolt
272 Hatch block
273 Tension frame
274 Spacer plate
275 Hatch cover
276 Davit brace
277 Davit
278 Handle
The hatches consist of obechi blocks or short pieces of
tube, fitted with additional die-cut ABS components; the
parts should be glued together using cyano. Make up the
individual hatches according to the detail drawings on the
plan.
- Glue together the oil tank entry hatch from parts 254 -
258, and place it on the hatch 62.
- Assemble the rudder compartment escape hatch from
parts 259 and 261, and glue it on the after deck in the
position shown in the plan view.
- Use parts 262 - 265 to make the after bulkhead escape
hatch, and glue the hatch in place as shown on the plan.
- Glue the cover 267 on the toolbox 266. The box cannot
be installed until the superstructure has been completed.
- Make up the freshwater tank hatch from parts 268 - 271.
Drill the 1 mm Ø holes for the handles 270 and the latch
Assembly instructions
Happy Hunter
- Drill 1.5 mm Ø holes for the bar supports in the after deck,
and glue the prepared hawser deflector bar assemblies in
them.
- Glue the large return roller 252 to the bar 248.
Material
Obechi
ABS
ABS
ABS
Aluminium
Plastic
Aluminium
Plastic
Obechi
ABS
Aluminium
Plastic
Obechi
ABS
Obechi
ABS
Brass
Brass
Obechi
ABS
ABS
ABS
ABS
ABS
Brass
bolt 271. Bend parts 270 and 271 to shape from pieces of
brass tube, and glue them in the holes.
- The forecastle deck hatch is assembled from parts 272 -
278. Please note: only one part on the "davit" sprue is
required for this model. Before gluing the tension frame
273 in place, drill the 3 mm Ø hole for the davit 277. Brace
the davit with the davit support 276. Drill 1 mm Ø holes in
the spacer plate 274 for the two handles 278.
- Glue the completed hatch to the forecastle deck.
40
Size in mm No.
off
43 x 43 x 15 1
1, die-cut 1
1.5, die-cut 1
1, die-cut 1
15 Ø 1
7 Ø 1
13 Ø x 1.4 x 11 1
7 Ø 1
16 x 16 x 12 1
1, die-cut 1
15 Ø 1
7 Ø 1
16 x 22 x 12 1
1, die-cut 1
18 x 18 x 12 1
1, die-cut 1
0.8 Ø 2
0.8 Ø 2
22 x 22 x 10 1
1, die-cut 1
1.5, die-cut 1
1, die-cut 1
1, die-cut 1
Inj. moulded 1
0.8 Ø 2
Order No.
1106
Notes
Machined
FS
FS
Machined
FS
As plan
As plan
As plan