ROBBE Happy Hunter Notice De Montage Et De Mise En Œuvre page 37

Forecastle deck and bulwark
Part Description
No.
190 Support rail
191 Forecastle deck
192 Chain halyard tube
193 Bulwark section
194 Handrail
195 Bulwark stanchion
196 Bulwark stanchion
197 - 200 Bulwark stanchion
201 Floor support
202 Base
203 Bulwark gusset
204 Bow bulwark
205 - 210 Bulwark stanchion
211 Bulwark fairing
The forecastle deck, Figs. 112 - 114
- Cut the support rail 190 to length and glue it in place cen-
trally as shown.
- Trim the forecastle deck 191 to fit and glue it in the hull.
Sand the rear edge flush with the foreship bulkhead.
- Drill the holes for the chain halyard tubes 192. Fit the
tubes, trim the ends and glue them in place. Apply a
watertight fillet of Stabilit-Express where the tubes meet
the anchor hawses. Sand back the top end of the tubes
flush with the forecastle deck.
Main deck bulwark, Figs. 115 - 120
- Cut out the scuppers in the bulwark sections 193. Trim
the bulwark sections to fit accurately in the hull (no gaps),
and glue them in place using Stabilit-Express.
- Cut out the scuppers in the hull itself to final size.
Removable main deck hatch, Figs. 125 - 127
Part Description
No.
212 Hatch base
213 - 214 Hatch side panel
215 Corner strip
- Drill 1.2 mm Ø holes in the hatch cover as shown.
- Note: the next step is to glue the side panels 213, 214 to
the hatch; check first that the hatch cover is the right way
up.
Hull stringers and stabilisers, Figs. 128 - 131
Part Description
No.
216 Fore-and-aft stringer, after deck
217 Fore-and-aft stringer, main deck
218 Fore-and-aft stringer, foredeck
219 Vertical rails
220 Fairing
221 Ram guard
222 Stabiliser
Assembly instructions
Happy Hunter
Material
ABS
ABS
Brass
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
ABS
- Trim the handrails 194 to fit, glue them in place and round
off the edges slightly.
- Trim the bulwark stanchions 195 - 200 to fit, bevel the
right-hand angled edge slightly, and glue them in place at
the marked points.
- Glue the floor supports 201 in place, and glue the bases
202 to them. Trim the gussets 203 to fit and glue them in
place.
The bow bulwark, Figs. 121 - 124
- Trim the bow bulwark 204 to fit neatly (no gaps). Cut the
hawse holes at the marked points.
- Fit the bulwark on the hull, align it carefully and tape it in
place on the outside. Glue the bulwark in place by running
cyano along on the inside.
- Trim the bulwark stanchions 205 - 210 and the bulwark
fairings 211 to size, and glue them in place as shown.
Material
ABS
ABS
ABS
- Glue the corner strips 215 in place.
- Clean up the completed hatch and place it temporarily on
the model.
Material
ABS
ABS
ABS
ABS
Obechi
Plastic
ABS
37
Size in mm No.
off
2 x 2 x 45 1
1.5, die-cut 1
7 Ø x 6.2 Ø 2
1, die-cut 2
2 x 2 x 450 2
1, die-cut 17
1, die-cut 1
1, die-cut 2 each
1, die-cut 4
1, die-cut 2
1, die-cut 4
1.5 1
1, die-cut 2 each
1, die-cut 2
Size in mm No.
off
1.5, die-cut 1
1.5, die-cut 2 each
4 x 4 x 11 4
Size in mm No.
off
2.9 x 6.5 x 910 2
2.9 x 6.5 x 480 2
2.1 x 4.5 x 150 2
2.1 x 4.5 30
3 x 8 x 10 2
40 x 18 2
3.5 x 7 x 325 2
Order No.
1106
Notes
Overlength
Vac. moulded
Notes
Notes
Rounded
Rounded
Rounded
As plan
FS
L-section