Publicité
Les langues disponibles
Les langues disponibles
The anchor winch, Figs. 133 - 136
Part
Description
No.
228
Split pin
229
Anchor winch base plate
230
Gearbox housing
231
End-support
232
Anchor winch shaft
233
Gearbox cover
234
Anchor winch hawse
235
Brace
236
Connecting piece
237
Lever
238
Brake spindle
239
Brake stand
240
Brake band
241
Handwheel
242
Sprocket
243
Anchor capstan
244
Chain stopper
245
Chain stopper crank
246
Anchor chain
247
Hall anchor
- Drill the appropriate holes in the base plate 229, the gear-
box housing 230 and the end-supports 231.
- Assemble the gearbox housing, the end-supports and the
base plate, together with the winch shaft 232, and glue
the parts together.
- Attach the gearbox cover 233 and the hawses 234. Cut
the brace 235 and the connecting piece 236 to shape and
glue them in place.
- Make the lever 237 by shortening a railing stanchion, and
glue it in a 1.2 mm Ø hole in the connecting piece 236.
- Shorten two railing stanchions above the central ball to
make the brake stands 239. Fit the brake spindles 238 in
the stands 239 with 2 mm projecting, set the parts at
right-angles and solder the joints.
- Cut the brake bands 240 to a length of 41.5 mm, and pier-
ce holes with a thick sewing needle at a point 2 mm from
the ends. Drill 1 mm Ø holes in the handwheels 241.
- Attach the sprockets 242 and the anchor capstans 243 in
such a way that the shaft 232 rotates freely.
- Attach the brake bands, the brake stands and the hand-
wheels.
The hawser deflector bars, Figs. 137 - 139
Part
Description
No.
248
Small hawser deflector bar
249
Large hawser deflector bar
250
Small hawser bar support
251
Large hawser bar support
252
Large return roller
Assembly instructions
Happy Hunter
Material
Brass
ABS
ABS
ABS
Brass
Aluminium
Brass
Spruce
ABS
Brass
Brass
Brass
Plastic
Plastic
Aluminium
Aluminium
Plastic
Brass
Metal
Metal
- Glue the completed anchor winch on the forecastle deck,
lining up the hawses with the chain halyard tubes.
The chain stoppers
- Glue the two-part chain stopper 244 together, and drill out
the 1 mm Ø hole for the chain stopper cranks.
- Make the cranks 245 from 1 mm Ø brass rod, and glue
them in the chain stoppers to form a mirror-image pair.
- The anchor chains 246 are required for aligning the chain
stoppers. The right-hand anchor is operated by connec-
ting the chain to the winch mechanism, whereas the left
anchor is static, i.e. it cannot be operated.
- Run the right-hand chain into the hull from above, and
attach it to the drum on the mechanism using the split pin
228. Wrap the chain around the right-hand sprocket, and
thread the chain stopper onto it. Route the chain down
and attach the Hall anchor 247 to it using a short piece of
thread.
- Attach the anchor and the chain stopper on the left-hand
side using a 150 mm length of chain.
- Glue the chain stoppers to the base plate 229 and the
forecastle deck as shown in the plan view.
Material
Brass
Brass
Brass
Brass
ABS
39
Size in mm
No.
off
1 Ø x 15
1
3, machined
1
3, machined
2
3, machined
2
2 Ø x 57
1
13 Ø, machined
2
3 Ø x 4
2
2 x 5 x 12
1
4 x 4 x 10
1
Mod. stanchion
1
1 Ø x 22
2
Mod. stanchion
2
2 x 0.4 x 41.5
2
7 Ø
2
15 Ø, machined
2
12 Ø, machined
2
Ready made
2
1 Ø
2
2.2 x 150
1 each FS
2.2 x 1300
Ready made
2
Size in mm
No.
off
2.57 x 0.5 x 4.22
1
2.57 x 0.5 x 4.22
1
1.5 Ø
2
1.5 Ø
2
Inj. moulded
2
Order No.
1106
Notes
FS
FS
FS
FS
FS
FS
FS
FS
FS
FS
FS
FS
FS
FS
FS
FS
As plan
FS
Notes
Oval, as plan
Oval, as plan
As plan
As plan
FS
Publicité
