Publicité
Les langues disponibles
Les langues disponibles
If any part has to be painted more than one colour, the joints
must be masked out using clear adhesive tape or PVC tape
- don't use paper masking tape! The tape must be removed
again when the paint is just touch-dry; do not allow the
paint to dry completely before peeling it off.
Joint areas of parts already painted must be sanded before
glue is applied.
The instructions inform you when particular parts have to be
painted before you continue with construction. Otherwise
you should paint the model at your own discretion.
Use only acrylic or synthetic enamel paints for this model.
Types designed for brush and spray application are equally
suitable.
If you have the facilities to apply a sprayed finish using a
spraygun and compressor, we recommend two-pack car
paints; use the same range of paints throughout the model.
We suggest that you copy the colour scheme shown in the
kit box illustration.
RC system
We strongly recommend that you install the specified RC
system components. If you intend to use items other than
those suggested, you can still use the arrangement shown
on the plan, but you may have to make allowance for minor
differences in component sizes.
Boatstand
Part
Description
No.
01
Base plate
02, 03
Hull support
04
Support strip
- Assemble the boatstand from parts 01 - 03 and glue the joints. The foam rubber strips for protecting the painted hull are not
required until later - Figs. 1 - 2.
Preparing the hull, power system
Part
Description
No.
1
Hull
2
Keel in-fill piece
3
Kort nozzle
4
Propeller shaft tube
5
Support
7
Speed controller support
6, 8
Speed controller support former
9
Speed controller support side
10
Speed controller support former
11
Motor bulkhead
12
Support former
13
Electric motor
14
Motor mounting screw
15
Washer
16
Capacitor / insulating sleeve
17
Capacitor / insulating sleeve
18
Red cable
19
Black cable
20
Connector
21
Coupling
22
Grubscrew
23
Lubricating tube
24
Propeller shaft
Assembly instructions
Happy Hunter
Connect the radio control system, set all the transmitter
sticks and trims to centre, and switch it on briefly. This sets
the servos to neutral from the outset.
All electrical connections inside the hull must be arranged in
such a way that they cannot come into contact with any
water which gets inside the boat.
Auxiliary working systems
The Happy Hunter is large enough to accommodate nume-
rous auxiliary working systems. You may wish to install a
working lighting system, crane, anchor winch, towing gear,
radar, siren, horn and bow thruster.
These instructions describe the installation of the working
systems at the appropriate point. We recommend that you
fit the working systems at an early stage, as installing them
later may be much more difficult due to restricted access.
Notes on the Parts Lists
PS = included in the Power Set
FS = included in the Fittings Set
Material
Birch ply
Birch ply
Foam rubber
Material
ABS
Balsa
Plastic
Brass
ABS
ABS
ABS
ABS
ABS
ABS
ABS
---
Steel
Brass
---
---
---
---
---
Aluminium
Steel
Brass
Steel
28
Size in mm
No.
off
8
1
8
1 each
6 x 4
2
Size in mm
No.
off
3, vac.-moulded
1
8 x 100 x 103
1
Inj. moulded
1 each Left / right
6.5 O.D. x 267
2
1.5, die-cut
1
1.5, die-cut
1
1.5, die-cut
1 each
1.5, die-cut
2
1.5, die-cut
1
3, machine-cut
1
3, machine-cut
2
Ready made
2
M4 x 10
4
4.3 x 9 x 0.8
4
100 nF
4
47 nF
2
1.5 mmÇ
1
1.5 mmÇ
1
Ready made
2 - 4 Not included
4 / 5 Ø x 17
2
M3 x 5
4
4 Ø x 0.4 x 55
2
4 Ø x 300
2
Order No.
1106
Notes
Notes
Oversize
PS
PS
PS
PS
PS
PS
PS, overlength
PS, overlength
PS
PS
PS
PS
Publicité
