Programming The Remote Controls; General Information; Memorising The Remote Controls - SOMFY ELIXO 3S M io Manuel D'installation

Elixo 3S M io
P16 Auxiliary output time delay
Values 0 to 60 value x 10 s = time delay value)
6: 60 s
Comments The auxiliary output time delay is only active if the value
selected for P15 is 2 or 6.
P19 Closing speed
P20 Opening speed
Values 1: slowest speed
to
10: fastest speed
Default value: 5
Comments Warning
If parameters P19 or P20 are changed, the installer
must check that the obstacle detection system
complies with appendix A of standard EN 12 453.
If necessary, install a safety edge and check that
compliance is obtained.
Failure to follow this instruction may result in seri-
ous injury, e.g. due to crushing by the gate.
P21 Closing slowdown zone
P22 Opening slowdown zone
Values 0: shortest slowdown zone
to
5: longest slowdown zone
Default value: 1
Warning
Comments
If parameters P21 or P22 are changed, the installer
must check that the obstacle detection system
complies with appendix A of standard EN 12 453.
If necessary, install a safety edge and check that
compliance is obtained.
Failure to follow this instruction may result in seri-
ous injury, e.g. due to crushing by the gate.
P25 Closing torque limitation
P26 Opening torque limitation
P27 Closing slowdown torque limitation
P28 Opening slowdown torque limitation
Values 1: minimum torque
to
10: maximum torque
Adjusted at the end of auto-programming
Warning
Comments
If parameters P25 to P32 are changed, the installer
must check that the obstacle detection system
complies with appendix A of standard EN 12 453.
If necessary, install a safety edge and check that
compliance is obtained.
Failure to follow this instruction may result in seri-
ous injury, e.g. due to crushing by the gate.
If the torque is too low, there may be erratic obstacle
detection.
If the torque is too high, the installation may not comply
with the standard.
Copyright © 2017 SOMFY ACTIVITES SA. All rights reserved.
P33 Obstacle detection sensitivity
Values 0: very low sensitivity
1: slightly sensitive
2: standard
3: very sensitive
Comments Warning
If parameter P33 is changed, the installer must
check that the obstacle detection system complies
with appendix A of standard EN 12 453. If necessary,
install a safety edge and check that compliance is
obtained.
Failure to follow this instruction may result in seri-
ous injury, e.g. due to crushing by the gate.
P37 Wired control inputs
0: complete cycle mode - pedestrian cycle
Values
1: opening mode - closing
Comments 0: terminal 11 input = complete cycle, terminal 9 input =
pedestrian cycle
1: terminal 9 input = opening only, terminal 11 input =
closing only
P40 Coupling speed when closing
P41 Coupling speed when opening
Values 1: slowest speed
to
4: fastest speed
Default value: 2
Warning
Comments
If parameters P40 or P41 are changed, the installer
must check that the obstacle detection system
complies with appendix A of standard EN 12 453.
If necessary, install a safety edge and check that
compliance is obtained.
Failure to follow this instruction may result in seri-
ous injury, e.g. due to crushing by the gate.
8. PROGRAMMING THE REMOTE CON-
TROLS

8.1. General information

8.1.1. Memorising the remote controls

There are two ways to memorise a remote control:
• Memorising via the programming interface.
• Memorising by copying a previously memorised remote control.
Each control button is memorised individually.
Memorising a button which has already been memorised will clear this
button's function.
8.1.2. Meaning of displayed codes
Code Designation
Add
Successful memorisation of a remote control
dEL Delete a previously memorised button
FuL
Memory full
EN
10