Level 1 Programming (On-Off Functions); Level 2 Programming (Adjustable Parameters) - Nice Naked Sliding Instructions Et Avertissements Pour L'installation Et L'utilisation

7.4 - Level one programming (ON-OFF functions)
Level 1 functions are all factory set to "OFF". However, they can be changed at
any time as shown in Table 6. Follow the procedure carefully, as there is a maxi-
01. Press the key "Set" and hold it down (approx. 3 s);
02. Release the "Set" key when "L1" LED starts flashing;
03. Press keys "▲" or "▼" to move the flashing LED onto the LED representing the function which is to be changed;
04. Press the "Set" key to change the state of the function:
(short flashing = OFF; long flashing = ON);
05. Wait 10 seconds before leaving the programme to allow the maximum time to lapse.
Note – Points 3 and 4 can be repeated during the same programming phases in order to set other functions to ON or OFF.
7.5 - Level two programming (adjustable parameters)
The adjustable parameters are factory set as shown in the table 7 with: "
However, they can be changed at any time as shown in Table 8. Follow the pro-
Imput Parameter LED
LED
L1 Pause
Time
L2 Step-by-
step
L3 Motor
speed
L4 Open Gate
Indicator
Output
L5 Motor
force
8 – English
TABLE 6 - Changing ON-OFF functions
TABLE 7 - Level two functions (adjustable parameters)
Value
(level)
L1 5 seconds
L2 15 seconds
L3 30 seconds
L4 45 seconds
L5 60 seconds
L6 80 seconds
L7 120 seconds
L8 180 seconds
L1 Open – stop – close – stop
L2 Open – stop – close – open
L3 Open – close – open – close
L4 Condominium operation
L5 Condominium operation 2 (more than 2" causes stop)
L6 Step-by-Step 2 (less than 2" causes partial opening)
L7 Man present
L8 "Semiautomatic" opening, "Man present " closing
L1 Very slow
L2 Slow
L3 Medium
L4 Fast
L5 Very fast
L6 Extremely Fast
L7 Opens "Fast"; closes "slow"
L8 Opens "Extremely Fast" Closes "Fast"
L1 Open Gate Indicator Function
L2 On if leaf closed
L3 On if leaf open
L4 Active with 2 nd radio output
L5 Active with 3 rd radio output
L6 Active with 4 th radio output
L7 Maintenance indicator
L8 Electric lock
L1 Super light gate
L2 "Very light" gate
L3 "Light" gate
L4 "Average" gate
L5 "Average-heavy" gate
L6 "Heavy" gate
L7 "Very heavy" gate
L8 "Super heavy" gate
mum time of 10 seconds between pressing one key and another. If a longer
period of time lapses, the procedure will finish automatically and memorize the
modifications made up to that stage.
cedure carefully, as there is a maximum time of 10 seconds between pressing
one key and another. If a longer period of time lapses, the procedure will finish
"
automatically and memorize the modifications made up to that stage.
SET 3 s
SET
L1
or
SET
10 s
Description
Adjusts the pause time, namely the
time which lapses before automatic
closure. This will only have an effect
if automatic closing is active.
Manages the sequence of controls
associated to the Step-by-Step input
or to the 1st radio command.
Adjusts the speed of the motor during
normal travel.
Adjusts the function associated with
the S.C.A. output (whatever the
associated function may be, the out-
put supplies a voltage of 24V –30
+50% with a maximum power of 4W
when active).
Adjusts the system which controls
the motor force in order to adapt it to
the weight of the gate. The force
control system also measures the
ambient temperature, automatically
increasing the force in the event of
particularly low temperatures.