Level 1 Programming (On-Off Functions); Level 2 Programming (Adjustable Parameters) - Nice Slight Instructions Et Avertissements Pour L'installation Et L'utilisation

8.4 - Level 1 programming (ON-OFF functions)
By default, level 1 functions are all set to OFF, but can be modified at any time
as described in Table 6. Take care during modification procedures, as there is a
01. Press and hold the "Set" key for about 3 seconds;
02. Release the "Set" key when the "L1" LED start to flash;
03. Press keys "s" or "t" to move the flashing LED onto the LED representing the function which is to be changed;
04. Press the "Set" key to change the status of the function: (short flashing = OFF; long flashing = ON);
05. Wait 10s to exit the programming mode automatically after the maximum time interval.
Note – Points 3 and 4 can be repeated during the same programming phases in order to set other functions to ON or OFF.
8.5 - Level 2 programming (adjustable parameters)
The adjustable parameters are factory set as shown in the Table 7 with: "
but can be modified at any time as shown in Table 8. Take care during modifi-
Input LED Parameter LED
L1 Pause
Time
L2 Function
STEP BY
STEP
L3 Speed
of motor
L4 Output
S.C.A.
L5 Force
of motor
8 – English
TABLE 6 - Changing ON-OFF Functions
TABLE 7 - Level 2 functions (adjustable parameters)
Value
(level)
L1 5 seconds
L2 15 seconds
L3
30 seconds
L4 45 seconds
L5 60 seconds
L6 80 seconds
L7
120 seconds
L8 180 seconds
L1
Open – stop – close – stop
L2 Open – stop – close – open
L3 Open – close – open – close
L4
Apartment block
L5 Apartment block 2 (more than 2" generates stop)
L6 Step-by-Step 2 (less than 2" causes partial opening)
L7 Hold-to-run
L8
"Semi-automatic" opening, "Man present " closing
L1 Very slow
L2
Slow
L3 Medium
L4 Fast
L5 Very fast
L6 Extremely Fast
L7 Opens "Fast"; closes "slow"
L8 Opens "Extremely Fast" Closes "Fast"
L1 Open Gate Indicator Function
L2
On if leaf closed
L3 On if leaf open
L4 Active with 2nd radio output
L5 Active with 3rd radio output
L6
Active with 4th radio output
L7 Maintenance indicator
L8 Electric lock
L1
Super light gate
L2 "Very light" gate
L3 "Light" gate
L4 "Average" gate
L5
"Averageheavy" gate
L6 "Heavy" gate
L7 "Very heavy" gate
L8
"Super heavy" gate
maximum time interval of 10 seconds between pressing one key and another;
otherwise the system exits the procedure automatically memorising the chang-
es made up to that time.
cation procedures, as there is a maximum time interval of 10 seconds between
pressing one key and another; otherwise the system exits the procedure auto-
"
matically memorising the changes made up to that time.
SET
3 s
SET
L1
or
SET
10 s
Description
Adjusts the pause time, namely the
time which lapses before automatic
closure. Is effective only if automatic
closure is enabled.
Manages the sequence of controls
associated to the Step-by-Step input
or to the 1st radio command.
Adjusts the speed of the motor during
normal travel.
Adjusts the function associated with
S.C.A. output. (whatever the associ-
ated function may be, the output
supplies a voltage of 24V –30 +50%
with a maximum power of 4W when
active).
Adjusts the system which controls
the motor force in order to adapt it
to the weight of the gate. The force
control system also measures the
ambient temperature, automatically
increasing the force in the event of
particularly low temperatures.