Safety Rules And Obligations Of The Installer; Information For The User; Residual Risks - Aprimatic R251FM Notice D'installation, D'utilisation Et D'entretien

SAFETY RULES AND OBLIGATIONS OF THE INSTALLER

To work in full compliance with the safety rules it is necessary to:
• wear protective clothing as provided for by law (safety footwear, goggles, gloves and helmet);
• do not wear clothing that can get caught (ties, bracelets, necklaces, etc.).
A motor-driven gate constitutes a machine and must be installed in accordance with the provisions of laws,
standards and regulations in force. Before installation, the on-site risk analysis must be carried out by
qualified professionals according to the current laws on motor-driven gates. To reach a suitable safety level,
the installation must be carried out in accordance with the provisions of Standards EN 12453 and EN 12445.
In non-EU countries, in addition to the mentioned standards, refer to national laws and regulations.
• Installation must be carried out by qualified professionals.
• Installation, electrical connections and adjustments must be carried out in compliance with the current laws and
regulations.
• Carefully read the instructions before starting installation.
• Incorrect installation may be dangerous.
• Packaging must not be abandoned in the environment but must be disposed of in compliance with the laws and
regulations in force.
• Before starting installation, check that the product and package are not damaged.
• Do not install the product in areas where there is a risk of explosion: the presence of flammable gases, dusts or
fumes poses a serious threat to the safety.
• Check that all the safety seals are present and that all the areas in which there are risks of shearing, crushing or
entrapment or any other risk are safeguarded or protected in compliance with the current regulations for motor
driven gates.
• It is mandatory to delimit properly the operation area to prevent access to unauthorised persons.
• The protection devices must be installed after an on-site risk analysis, checking that they are marked and operate in
compliance with the current regulations.
• On each installation the data required by the applicable regulations must be affixed in a visible manner.
• Before connecting to the power supply line, check that the power available is consistent with the nameplate date.
• Check that a suitable differential magneto-thermal switch is present upstream of the installation.
• The manufacturer of the drive declines any responsibility if components incompatible with safe and correct
operation are used.
• The installer must provide the user with all the necessary information about the use of the automation, with special
care for the manual emergency manoeuvre and any residual risks.

INFORMATION FOR THE USER

• The instructions and warnings below are an integral and essential part of the product. The instructions and
warnings must be given to the user and then read carefully because they include important warnings for use and
maintenance. Such instructions must be kept and transferred to any future users.
• Use this automation for the permitted uses only. All other uses constitute improper and hazardous use.
• Avoid standing near mechanical moving parts. Do not enter the operating range of the moving automation. Do not try to
hinder or obstruct the automation movement as it can be a source of danger.
• Do not allow children to play or stand in the operating range of the automation.
• Keep remote control and other control units in a safe place to prevent use by children or unauthorised people.
• In the event of any faults, disconnect the operator from the mains power supply using the main switch. Do not
attempt to repair the equipment and contact the installer or other specialist assistance centre. Failure to follow these
instructions may result in hazardous situations.
• All repair and maintenance operations, including those for drive cleaning, must be carried out by qualified personnel
only.
• To ensure a correct and efficient operation, it is necessary to follow the manufacturer instructions and in particular
have periodic maintenance performed by specialised personnel that checks, above all, the smooth operation of
protection devices.
•
The equipment can be used by children who are over 8 years of age and by persons with limited physical, sensory
or mental capacities, or inexperienced or unskilled persons, provided that they are under supervision or that they
have been instructed about the safe use of the equipment and inherent hazards. Children must be supervised so
that they do not play both with the equipment and the remote control. Cleaning and maintenance operations
intended to be carried out by the user must not be performed by unsupervised children.
!
Warning

RESIDUAL RISKS

During gate opening, the area in which the operator gear operates is dangerous for anyone who
imprudently puts his/her hands or any other body part near this area.
R251
SWING GATES
-13-