Maintenance; Malfunctions; Transport And Storage - Tunturi F20 Mode D'emploi

Masquer les pouces Voir aussi pour F20:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 12
calculation can be started only if the heart rate
measurement is activated and the heart rate value
is shown on the display The measurement takes 60
seconds. After 60 seconds, the display shows your
recovery index F1-F6 (F1 = best result). To get back
to main menu, press RECOVERY button once again.
SETTING THE DATE AND TIME
After pressing RESET button for 2 seconds, the meter
restarts and you can use +/- ENTER to set the date
and time.
ADDITIONAL NOTES
1. For speed and distance you can choose either
metric or English units by using the KM/ML switch
located on the back cover of the meter. Batteries
have to be reinstalled to apply the change.
2. If you are not training and buttons are not
pressed, the meter switches into the sleep mode
after four minutes. Room temperature, date and
time are displayed.
3. Entering training targets (time, distance, energy,
heart rate limit) is possible only in the STOP mode
(not during training).
4. When you are in STOP mode, Pause-symbol (P) is
displayed on the upper left corner of the display.
5. SCAN symbol is displayed on the upper left corner
of the display, when scan function is on. You can
switch the scan function off by pressing ENTER.
6. This equipment cannot be used for therapeutic
purposes.
7. Energy expenditure is calculated based on
average values. The energy expenditure is displayed
in kilocalories. To convert this into joules, use the
formula: 1 Kcal = 4.187 KJ.
8. If you are training with heart rate measurement
you can set maximum heart rate limit. When limit is
exceeded while training meter will give alarm beeps.
9. If you have several targets to count down, a
signal sounds when each target reaches zero. After
reaching zero each value starts to count up.
10. Note that recovery index is in relation to the
heart rate frequency in both the beginning and the
end of the measurement.

MAINTENANCE

The equipment requires very little maintenance.
Check, however, from time-to-time that all screws
and nuts are tight.
After exercising, clean the equipment with a soft,
absorbent cloth. Do not use solvents.
Never remove the equipment's protective casing.
O W N E R ' S M A N U A L
REPLACING BATTERIES
Replace the meter batteries if the meter no longer
starts or if the display becomes disturbingly dim.
Remove the battery casing cover from the back
and remove the old batteries. Insert new batteries
into the battery holder and push the battery
casing cover back into place. IMPORTANT: Note the
indications + and – marked on the battery holder.

MALFUNCTIONS

Despite continuous quality control, defects and
malfunctions caused by individual components may
occur in the equipment. In most cases it's unnecessary
to take the whole device in for repair, as it's usually
sufficient to replace the defective part.
If the equipment does not function properly during use,
contact your Tunturi dealer immediately. Always give
the model and serial number of your equipment. Please
state also the nature of the problem, conditions of use
and purchase date.
If you require spare parts, always give the model, serial
number of your equipment and the spare part number
for the part you need. The spare part list is at the back
of this manual. Use only spare parts mentioned in the
spare part list.

TRANSpORT AND STORAGE

Please follow these instructions when carrying and
moving the cycle about, because lifting it incorrectly
may strain your back or risk other accidents:
Stand behind the equipment. Grip the seat with
one hand and the handlebar with the other, and set
your foot on the rear support. Tilt the equipment
so that it rests on its transport wheels. Wheel the
equipment to move it, on these transport wheels.
Lower the equipment while holding on to the
handlebar and remain behind the equipment all the
time.
Transport the equipment with caution
NOTE!
over uneven surfaces, for example over a step. The
equipment should never be transported upstairs
using the wheels over the steps, instead it must be
carried. We recommend that you use a protective
base when transporting the equipment.
To prevent the equipment malfunctioning, store in a dry
place with as little temperature variation as possible and
protected from dust.
GB
F 2 0
5

Publicité

Table des Matières
loading

Table des Matières