Operation; Cleaning And Maintenance; Defects And Malfunctions; Transport And Storage - Tunturi F20 Mode D'emploi

Operation

Power on
- Press any key to power on the console when being in sleep mode..
- Start pedaling to power on the console when being in sleep mode.
LCD will display all segments as Drawing.
Power off
Without any signal being transmitted into the monitor for 4 minutes
the monitor will enter SLEEP mode automatically.
User Profile setting
- Use UP or DOWN (Dail) to set SEX, HEIGHT, WEIGHT and AGE.
- Press MODE/ENTER to confirm.
Workout setting
- Press MODE/ ENTER key to select the function of TIME,
DISTANCE, CALORIES, and PULSE. Use UP or DOWN (DAIL) for
setting and press MODE/ENTER key for confirmation.
- For instance the time set-up, when the time value is blinking, you
can use UP and DOWN (DAIL) to adjust the number. Press MODE/
ENTER key for confirmation and skip to next set-up. The set-up of
DISTANCE, CALORIES and PULSE is the same as TIME set-up.
- Once the workout begins and the console picks up the exercise
signal, the value of SPEED/RPM, TIME, DST and CAL will count up
on the display.
Recovery
- The RECOVERY key will only be valid if pulse is detected.
- TIME will show „0:60" (seconds) and counts down to 0.
- Computer will show F1 to F6 after the countdown to test heart rate
recovery status. User can find the heart rate recovery level based
on the chart below.
- Press RECOVERY key again to return to the beginning.
F1 Outstanding
F2 Excellent
F3 Good
F4 Fair
F5 Below average
F6 Poor
Body Fat
- Press the BODY FAT key to start body fat measurement.
- During measuring, users have to hold both hands on the hand
grips. LCD display "-" "- -" "- - -" "- - - -" for 8 seconds until
computer finish measuring.
- LCD will display BMI and FAT %.
Body fat mode error codes
- *E-1
There is no heart rate signal input detected.
- *E-4
Occurs when FAT% and BMI result is below 5 or exceeds 50.

Cleaning and maintenance

The equipment does not require special maintenance. The
equipment does not require recalibration when it is assembled, used
and serviced according to the instructions.
⚠ WARNING
• Do not use solvents to clean the equipment.
- Clean the equipment with a soft, absorbent cloth after each use.
- Regularly check that all screws and nuts
are tight.
- If necessary, lubricate the joints.

Defects and malfunctions

Despite continuous quality control, defects and malfunctions caused
by individual parts can occur in the equipment. In most cases, it will
be sufficient to replace the defective part.
- If the equipment does not function properly, immediately contact
the dealer.
- Provide the model number and the serial number of the equipment
to the dealer. State the nature of the problem, conditions of use
and purchase date.
Trouble shooting:
- When the display of LCD is dim, it means the batteries need to be
changed.
- If there is no signal when you pedal, please check if the cable is
well connected.
‼ NOTE
• When stop training for 4 minutes, the main screen will be off.
• If the computer displays abnormally, please re-install the
batteries and try again.
Shaky or unstable feeling during use
If the machine feels unstable or unstable during operation, it is
advisable to adjust the support feet to bring the frame to the correct
height. Read the instructions in this manual in section: "Use"

Transport and storage

⚠ WARNING
• Carry and move the equipment with at least two persons.
- Remain standing in front of the equipment on each side and take
a sturdy grip at the handlebars. Tilt the front of the equipment
so as to lift the rear of the equipment on the wheels. Move the
equipment and carefully put the equipment down. Place the
equipment on a protective base to prevent damage to the floor
surface.
- Move the equipment carefully over uneven surfaces. Do not move
the equipment upstairs using the wheels, but carry the equipment
by the handlebars.
1 9
English