Weight Unit Toggle Mode; Dimensions Unit Toggle Mode; Spin Count Functions; Counter Functions - Accu-Turn 1500 Manuel De L'opérateur

5.4.2-7
5.4.2-8
5.4.2-9
54
Operations
Step 6: Step 6:
Minimization completed (Figure 5.4.2-7): Minimization completed (Figure 5.4.2-7):
• Exit Minimization Mode. • Exit Minimization Mode.
Minimization to be continued (Figure 5.4.2-8): Minimization to be continued (Figure 5.4.2-8):
• Rotate the wheel until "888" is displayed. • Rotate the wheel until "888" is displayed.
• Double mark the tire at the 12 o'clock position. • Double mark the tire at the 12 o'clock position.
• Remove the wheel from the unit. • Remove the wheel from the unit.
• Use a tire changer to rotate the tire so that the • Use a tire changer to rotate the tire so that the
double mark is in line with the valve. double mark is in line with the valve.
• Mount the wheel on the balancer. • Mount the wheel on the balancer.
• Select the "F" key. • Select the "F" key.
Step 7 (Figure 5.4.2-2):
• Rotate the valve to the 12 o'clock position.
Step 7 (Figure 5.4.2-2):
• Select the "F" key. • Rotate the valve to the 12 o'clock position.
• Select the "F" key.
Step 8 (Figure 5.4.2-3):
• Spin the wheel.
Step 9 (Figure 5.4.2-9): Step 8 (Figure 5.4.2-3):
• Spin the wheel.
The unit will display the result:
- - - Minimization successfully completed
EEE Minimization failed. Step 9 (Figure 5.4.2-9):
The unit will display the result:
- - - Minimization successfully completed
5.4.2

Weight Unit Toggle Mode.

EEE Minimization failed.
Default weight setting: ounces
Select this mode to change the unit of measurement
for the weight, before or after spinning the wheel.
• Hold down the " F " key and press the "- Gr/Oz" key
5.4.2 Weight Unit Toggle Mode.
to switch to grams.
Repeat the procedure to switch back to ounces.
Default weight setting: ounces.
Select this mode to change the unit of measurement
5.4.3

Dimensions Unit Toggle Mode.

for the weight, before or after spinning the wheel.
Default diameter and width unit of measurement:
• Hold down the "F" key and press the "Gr/Oz" key.
inches.
Repeat the procedure to switch back to ounces.
• Hold down the " F " key and press the "-" mm-inch
key to switch to millimeters.
Repeat the procedure to switch back to inches.
5.4.3 Dimensions Unit Toggle Mode.
5.4.4

Spin Count Functions.

Default diameter and width unit of measurement:
Use this function to access the internal spin count
inches.
functions programmed into the balancer software.
• With the machine on, simultaneously press "F" and
• Hold down the "F" key and press the "mm-inch"
"FINE".
key
The machine will display "C" on the left display, it will
Repeat the procedure to switch back to inches.
soon disappear and the number of measuring runs
performed to date will appear.
The available memory functions can be scrolled in both
directions.
• Press "+" or "–" of Offset.
5.4.4

Counter Functions

The available counters in order are:
This section covers the use of counters, important
C1 -Total machine spins since manufacturing.
for analysing the history of unit processes.
C2 -Number of spins ending with 0 (zero) unbalance
The machine saves a large amount of data
results.
accumulated from the functions previously performed.
C3 -Number of times weight minimization mode has
Even after a short period of work, thanks to this
been selected.
function, you can poll the machine and obtain data
C4 -Function reserved for service technicians.
useful for statistical purposes regarding work done in
C5 -Function reserved for service technicians.
the workshop, or for machine maintenance.
Operator's Manual ACCU 1500