Operating, Inspecting And Monitoring The Machine; Working With The Machine - Hettich BlueMax Mini Modular Instructions De Service

• When performing set-up work or changing a tool,
thoroughly clean the immediate area of the machine you
are working on. The proper way to do this is by suction,
never by blowing it clean with compressed air. Dust deposits
can cause malfunctions and / or damage to property during
later operation.
• Always make sure tools are securely fastened.
• Completely remove any assembly or servicing aids, tools,
cleaning cloths, assembly waste etc. from the machine.
• Make sure all components can move freely.
• After completing all connecting, set-up, servicing and / or
repair work, check the machine to make sure it is safe and
ready to operate.
• Check all guards for proper attachment.
• Moving / rotating machine elements that cannot be covered
for operating reasons always present a source of danger
with a major risk of injury from pinching, cutting, shearing,
snatching, catching, winding or attack points.
• Carry out function checks and trial run as instructed and,
in particular, make sure the safety guards are in proper
working order.
• Familiarise yourself with possible switching errors and how
to avoid them as well as with the measures necessary in the
event of faulty operating results.
• After completing function checks / trial run, return the
machine to a state of operational readiness for the operator
and, if necessary, draw the operator's attention to any
changes to machine handling.

15. Operating, inspecting and monitoring the machine

Danger!
Never leave the machine unattended while it is
running. Avoid touching any moving / rotating
components.
Only put the machine into operation once it has been
installed and connected and all servicing measures have been
completed.
When starting the machine and putting it into operation,
make sure there are no persons working on the machine or at
risk from the machine starting.
Only switch the machine on after making sure that
• any malfunctions have been fully rectified,
• set-up and servicing work have been properly completed,
• worn and / or damaged components have been replaced,
• all protective equipment and safety guards are in proper
working order.
Danger!
Never get a second person to switch the machine on
if you need to perform set-up or servicing work in the
danger zone.
When performing any action, always remember that you
could get trapped between moving machine parts and
stationary boundaries (building, guards etc.).

16. Working with the machine

Do not place any pallets or other objects in the safety zone
of at least 1.0 metre between moving machine parts and
stationary boundaries (walls, pillars, other machines or guards
etc.).
Danger!
An activated machine (master switch or power supply
ON) can start moving at any time.
Only operate the machine with the safety guards provided at
the site of installation.
Danger!
Smoking or any other use of fire, naked flame or other
ignition sources are prohibited at the place where the
machine is installed.
During operation, remove dust deposits at regular intervals to
be defined by the owner. Pay attention to fire and explosion
protection.
Only check component quality once the machine is standing
still and has been made safe or after the component has left
the machine and has been safely set down.
Always use the recommended personal protective
equipment, such as safety goggles, protective clothing, ear
protection, safety shoes etc. while you are operating the
machine.
Never reach into the running machine or behind claddings /
covers and other places you are unable to see into.
Danger!
Risk of injury for crushing and cutting points
Never touch
• tools before the machine has reliably come to a complete
standstill,
• components at operating temperature, such as drilling units.
Immediately shut the machine down, turn the master / mains
switch off
• in the event of abnormal / unusual operating behaviour,
noises or vibrations,
• if tools are damaged or improperly fastened,
• in the event of a faulty power / compressed-air supply.
• Establish the cause of the trouble and, to satisfy safety
requirements, instruct qualified, skilled personnel to rectify
such in the proper manner and in full or inform
Hettich FurnTech GmbH & Co. KG.
• The machine must only be restarted after fully eliminating
defects or damage.
Before leaving the place of operation, switch the machine
off and employ suitable measures to ensure that this state
cannot be altered inadvertently or by unauthorised persons.
107 107