Publicité
4
P
REPARATION
4.1
S
COPE OF DELIVERY
S
COPE OF DELIVERY
-
One Chassis
-
3,5 ccm two stroke glow engine
with 1,4 kW (1,9 HP), with
manifold, resonance tube, air filter and pull starter,
already mounted
-
Steering servo, Throttle/brake servo and receiver,
already mounted
-
fuel hoses, already laid.
-
Four wheels with already mounted and pre-glued
Buggy tires,
-
Buggy body, imprinted
-
Splints to fasten car body
-
A plastic tube as guidance for the wire aerial
one two-channel remote control
-
(pistol grip transmitter)
-
This operating manual
S
P
PARE
ARTS
The spare part list can be found on our Website www.conrad.com in the Download domain specific to the
corresponding product. Alternatively, you can order the spare parts by phone; the contact details are at the
beginning of this operating manual in chapter "Introduction".
A
CCESSORY RECOMMENDATION
Which type of fuel is the right one?
The selection of the fuel has an impact on the performance characteristic of the engine.
However, as a matter of principle:
-
In the running-in phase, a special RC car fuel with approximately 16% nitromethane should be used.
-
After the run-in of the engine (after a mere operating time of approximately 45 minutes), you can change to a fuel
with approximately 20% nitromethane.
-
For maximum output, we recommend the max. percentage of 25% nitromethane
Use fuel for RC cars only!
The percentage of oil contained in fuel for RC plane engines is too small (too little lubrication), which causes the
engine to overheat, thus leading to serious damages.
The same is valid for vehicle gasoline.
Why is a tank bottle needed?
RC model car fuel is available in big bulks (canisters) only. Filling the tank by using a smaller, special
tank bottle with a small, curved pouring tube is significantly simpler. You also prevent spilling fuel
(expensive and poisonous).
Are more glow plugs necessary?
Glow plugs wear, especially in the running-in phase. Therefore, we recommend having some glow
plugs ready in case of need for a replacement. There are glow plugs with different calorific values;
the selection of the glow plug has a big impact on driving performance. For the running-in phase, you
should use a "hot" glow plug for high performance engines. After the running-in phase, you can use a
glow plug with a middle or a "cold" calorific value.
Use glow plugs for RC cars only! A wrong glow plug, such as e.g. for 4 stroke plane engines, lets the engine
run incorrectly and complicates the tuning.
Replacing the glow plug
To that effect, you need an extra long plug spanner (spider wrench SW 8, 9, 10 and 12), which can be
used also to unscrew the outer hexagonal screws.
Preheating the glow plug
A plug connector (long) with rechargeable battery as a unit is inserted on the glow plug and heats the
latter, so that the air-fuel mix sparks off and the engine starts. When the engine runs smoothly, the plug
connector can be removed.
© REELY 09/07
All manuals and user guides at all-guides.com
,
NECESSARY ACCESSORIES
R
EQUIRED ACCESSORIES
N
OT INCLUDED IN THE DELIVERY
-
-
-
-
-
-
Also available as a complete set
Nitrobox II Combuster no. 23 07 99
incl. transport box
-
-
12 accumulators for the transmitter and the receiver
Glow plug (cold to supercold) and
plug spanner
Plug connector with rechargeable battery as a unit
and
battery charger
Tank bottle
Charger (220V) for the rechargeable batteries or
quick charger to connect to a 12V car battery
Model fuel methanol/oil based,
16% - 25% nitromethane
:
43
Publicité
