Barbecook SPRING 300 CREME Mode D'emploi page 11

Set the control knob of one burner to HIGH.
5
Always light one main burner to start with. Never light all
1
main burners at the same time.
If the burner does not light within 5 seconds, set its control
6
knob to OFF, close the gas supply and wait 5 minutes. This
allows any accumulated gas to escape.
Retry lighting the burner. If it still does not light, refer to
7
"14 Troubleshooting" to determine the cause of the problem.
Once one burner is lit, light the other burners by setting their
8
control knobs to HIGH.
9.3 Lighting the side burner
This information does not apply to the Spring 300. That appliance
is not equipped with a side burner.
The side burner can only carry vessels with a maximum
1
weight of 9 kg and a maximum diameter of 220 mm.
9.3.1 U
SING THE IGNITER
Open the lid and set the control knob of the side burner to
1
OFF.
If no other burner is lit yet, open the gas supply and wait ten
2
seconds. This allows the gas to stabilize.
Press the igniter until you hear sparks.
3
While holding the igniter, set the control knob of the side
4
burner to HIGH.
If the burner does not light after three attempts, set its
5
control knob to OFF, close the gas supply and wait 5
minutes. This allows any accumulated gas to escape.
Retry lighting the side burner. If it still does not light, try
6
lighting it with a match or refer to "14 Troubleshooting" to
determine the cause of the problem.
9.3.2 U
SING A MATCH
Place a match in the match holder.
1
Open the lid and set the control knob of the side burner to
2
OFF.
If no other burner is lit yet, open the gas supply and wait ten
3
seconds. This allows the gas to stabilize.
Light the match and hold it about 13 mm from the side
4
burner.
Set the control knob of the side burner to HIGH.
5
If the side burner does not light within 5 seconds, set its
6
control knob to OFF, close the gas supply and wait 5
minutes. This allows any accumulated gas to escape.
Retry lighting the side burner. If it still does not light, refer to
7
"14 Troubleshooting" to determine the cause of the problem.
9.4 Switching the burners off
If you no longer use the burners, you have to switch them off.
Proceed as follows:
Close the gas supply.
1
Set the control knobs of the burners to OFF.
2
By closing the gas supply first, you make sure there is no
2
gas left in the appliance.
9.5 Relighting the burners
If a burner goes out while in use, proceed as follows:
Open the lid and close the gas supply.
1
Set all control knobs to OFF and wait 5 minutes. This allows
2
any accumulated gas to escape.
Relight the burner(s).
3
9.6 Checking the flames
Each time you light a burner, you have to check its flames. A
perfect flame is almost completely blue, with some yellow at the
top. Sporadic yellow flames are normal and not harmful.
If there is something wrong with the flames, do one of the
following to solve the problem:
If the flames are...
Low and entirely yellow
Higher than the bowl
www.barbecook.com
Do the following...
Immediately close the gas supply and
1
set all control knobs to OFF.
Refer to "14 Troubleshooting" to
2
determine the cause of the problem.
Most likely, the venturis are blocked.
Immediately close the gas supply and
1
set all control knobs to OFF.
Wait 5 minutes to allow any
2
accumulated gas to escape.
Relight the burner(s).
3
If the problem persists, refer to
4
"14 Troubleshooting" to determine
the cause of the problem.
LOW HIGH
11