Grounding The Unit; Flooring - Monogram ZIR241NPNII Instructions D'installation

Installation Instructions - Dual Retro-Fit Installation
REFRIGERATOR/FREEZER LOCATION
Do not install the refrigerator/freezer where the tem-
perature will go below 55°F (13°C). It will not run
often enough to maintain proper temperatures.
Do not install the refrigerator/freezer where
temperatures will go above 100°F (37°C). It will not
perform properly.
Do not install the refrigerator/freezer in a location
exposed to water (rain, etc.) or direct sunlight.
Install it on a floor strong enough to support it fully
loaded.
TOOLS AND MATERIALS REQUIRED
• Metal shears
• #1, #2 Phillips screwdriver
• Flathead screwdriver
• Putty knife
• Measuring tape
• Drill and 1/16", 5/64", 3/16", 1/2" bits
• 5/32" concrete bit (if installing anti-tip into concrete)
• 1/4", 3/8", 7/16" driver/socket
• 7/16" open wrench
• T20, T30 driver/bit
• 1/8", 1/4" hex driver (allen wrench)
• Level
• Water shut-off valves (optional but recommended)
• 8' waterline (one per unit requiring water hookup)
• Masking tape
• Rubbing alcohol
• Adjustable wrench
• Center punch
• Heater Unification Kit (ZKUN)
• Stainless Steel Door Kits (if applicable)
• Custom panels for doors (if applicable)
• Handle Kits (if applicable)
• 42" (ZKR42N) or 48" (ZKR48N) Trim Retro Kit
42" (ZKK42P) or 48" (ZKK48P) Stainless Steel Toe Kick
HARDWARE SUPPLIED (per unit)
• Water Filter Bypass Plug (if equipped)
• Air filter (if equipped)
• Anti-Tip bracket
• 3 Lag screws
• 3 Tapcon screws
• 3 Toggles with bolts
• 1 Hair Pin Cotter
• 1 Retaining pin
• Panel installation templates
• 2 Door trims
• 2 Door panel brackets
• Set screws
• #6 Phillips head wood screws

GROUNDING THE UNIT

WARNING
Hazard.
Failure to follow these instructions can
result in death, fire, or electrical shock.
The power cord of this appliance is equipped with a
3-prong (grounding) plug which mates with a standard
3-prong (grounding) wall receptacle to minimize the
possibility of electric shock hazard from this appliance.
Have the wall outlet and circuit checked by a qualified
electrician to make sure the outlet is properly grounded.
Where a standard 2-prong wall outlet is encountered, it
is your personal responsibility and obligation to have it
replaced with a properly grounded 3-prong wall outlet.
DO NOT, UNDER ANY CIRCUMSTANCES,
CUT OR REMOVE THE THIRD (GROUND)
PRONG
FROM THE POWER CORD.
DO NOT USE AN ADAPTER PLUG TO
CONNECT THE REFRIGERATOR TO A
2-PRONG OUTLET.
DO NOT USE AN EXTENSION CORD WITH
THIS APPLIANCE.

FLOORING

For proper installation, this product must be placed
on a level surface of hard material that is at the same
height as the rest of the flooring. This surface should
be strong enough to support a fully loaded refrigerator
or freezer, or approximately 1,200 lbs. per unit.
NOTE: Protect the finish of the flooring.
NOTE: Not recommended for installation on carpeted
flooring.
• Door Bracket Cover Top
• T30 screws
• 1 Hinge limiter pin
• Center door panel bracket
• Hi-Lo screw and square washer
• Access Cover
• Painted access cover screws
26
Electrical Shock
31-1000190 Rev. 2