Installation: Control Panel And Accessories; Preliminary Checks Before Installation And Limitations On Use; Description Of The Control Panel - Nice HSCU2 Instructions Et Avertissements Pour L'installation Et L'utilisation

4

INSTALLATION: control panel and accessories

4.1 - Setting up the system components for configuration
Since the system components communicate wirelessly, it is best to configure
the system first on the bench and only then locate and install the devices .
For control panels which also have electrical connections, proceed as
follows:
1) configure the wireless devices on the bench;
2) mount all devices;
3) make the electrical hookup .
To avoid errors, malfunctions and reception failures, proceed as follows:
This procedure checks the radio coverage of the devices before their
installation .
a) Place all products on the bench with their packaging open;
b) Insert the "SIM" card for the GSM version (see figure 10);
Caution - the SIM card's PIN must be cancelled, along with any messages,
contacts and other resident or saved information .
Caution - 3G SIM cards are not compatible .
c) Power up the control panel and program it (for programming refer to Chap-
ter 6 - "Alarm system programming");
d) Insert the batteries into the devices so that the control panel can acquire
them one by one;
e) Test the operation of the various devices;
f) Place the control panel in its intended location (do not mount it there yet);
g) Place the other devices in their intended positions (again, without mounting
them yet);
h) Check that every device has sufficiently wireless reception to operate (see
"Testing the control panel");
In GSM models, check that there is sufficient reception:
i) Now install all devices in place;
The following paragraphs describe the installation of the control panel (all mod-
els) and the electrical hookup of wired versions .

4.2 - Preliminary checks before installation and limitations on use

Before proceeding with installation, check the condition of the product, suit-
ability of the selected model and conditions of the intended installation environ-
ment .
• Check that all conditions fall within the "limits of use" and "technical charac-
teristics" .
• Check that the installation location is compatible with the overall clearance
of the product .
• Check that the mounting surface is solid, so that the device is mounted
securely and is protected against impact .
• Install the control panel at least 1 m off the ground .
• the product may only be used with Nice Home Security system devices .

4.3 - Description of the control panel

All control panel models are fitted with system memory boards .
During programming, the card stores the system parameters (excluding voice
messages recorded by the installer or user) and can be transferred from one
control panel to another . Before removing or inserting the board make sure that
the control panel is off and not powered .
Some control panel models (models HSCU2GC and HSCU2G) are equipped
with a GSM telephone dialler .
The SIM card must be inserted before starting installation and with the power
off . The SIM card may be provided by any cellular operator and with any con-
tract (the system only uses the voice and SMS services), but must be config-
ured with PIN code = "1234" or set as "access without PIN": this can be
done by inserting the SIM card in any GSM phone .
Fig. 6A models HSCU2GW and HSCU2W
Fig. 6B models HSCU2GC and HSCU2C
a - Microphone
b - Socket for PSTN telephone line
c - Hole for cable routing
d - PC connection socket
e - Terminal board for electrical connections (mod. HSCU2C and HSCU2GC)
f - Internal siren
g - Speaker
h - System memory board
i - GSM SIM (mod. HSCU2GW and HSCU2GC)
l - Battery pack (mod. HSCU2GW and HSCU2W)
m - Backup battery (mod. HSCU2GC and HSCU2C)
n - Mains power terminal (mod. HSCU2GC and HSCU2C)
o - Power supply unit (mod. HSCU2GC and HSCU2C)
p - GSM aerial (mod. HSCU2GW and HSCU2GC)
Model HSCU2GW and HSCU2W
6A
p
a
b
d
Model HSCU2GC and HSCU2C
6B
p
a
b
c
d
l
i
h
g
f
o
n
m
i
h
g
f
e
English – 11